Item

NZ200

Control Mode

Sensorless flux vector control(SFVC)

Voltage/Frequency (V/F) Control

Maximum frequency

0～600Hz

Carrier frequency

0.5kHz～16kHz

The carrier frequency is automatically adjusted based on the load features

Input frequency resolution

Digital setting:0.01Hz

Analog setting: maximum frequency×0.025%

Startup torque

G type:0.5Hz/150%(SFVC)

P type:0.5Hz/100%

Speed range

1:100(SFVC)

Speed stability accuracy

±0.5%(SFVC)

Overload capacity

G type:60s for 150% of the rated current, 3s for 180% of the rated current.

P type:60s for 120% of the rated current, 3s for 150% of the rated current.

Torque boost

Fixed boost

Customized boost 0.1%~30.0%

V/F curve

Straight-line V/F curve

Multi-point V/F curve

N-power V/F curve (1.2-power, 1.4-power, 1.6-power,

1.8-power, square)

V/F separation

Two types: complete separation; half separation

Acceleration and deceleration curves

Straight-line ramp

S-curve ramp

Four groups of acceleration/deceleration time with the range of 0.0–6500.0s

DC braking

DC braking frequency: 0.00 Hz to maximum frequency

Braking time: 0.0–36.0s

Braking action current value: 0.0%–100.0%

JOG control

JOG frequency range: 0.00–50.00 Hz

JOG acceleration/deceleration time: 0.0–6500.0s

PLC,Multiple preset speeds

It implements up to 16 speeds via the simple PLC function or by input(X) terminal states

Built-in PID

It realizes process-controlled closed loop control system easily.

Auto voltage
regulation (AVR)

It can keep constant output voltage automatically when the mains voltage changes.

Over-voltage/
Over-current stall
control

The current and voltage are limited automatically during the running process so as to avoid frequent tripping due to over-voltage/over-current.

Torque limit and
control

It can limit the torque automatically and prevent frequent over-current tripping during the running process.

High performance

Control of asynchronous motor is implemented through the high-performance current vector control technology

Instantaneous blackout doesn’t stop

The load feedback energy compensates the voltage reduction so that the AC drive can continue to run for a
short time.

Rapid current limit

It helps to avoid frequent over-current faults of the AC drive.

Timing control

Time range: 0.0–6500.0 minutes

Communication methods

 RS -485

Running command channel

Given by the panel, control terminals,

Serial communication port, can be switched by many ways

 Frequency source

Kinds of frequency source, given by

Digital analog voltage, analog current, serial port. can be switched by many ways

 Auxiliary frequency source

10 kinds of Frequency source, can easily realize Micro adjustment, frequency Synthesizer

Input terminals

37 kw and below:

4 digital input terminals;

1 analog input terminal, Support 0～10V voltage input or 4～20mA current input(AVI)

45 kw and above:

6 digital input terminals,one of them supports up to 100kHz high-speed pulse input (S3 optional)

Two analog input terminals: one supports 0 to 10V voltage input (FIV), and the other supports 0 to 10V voltage input or 4 to 20mA current input (FIC). 

Output terminals

37KW and below: 

1 relay output terminal (RA, RC); 

45KW and above: 

1 digital output terminal (MO1) 

1 relay output terminal (RA, RB, RC) 

1 analog output terminal, supporting 0 to 20mA current output or 0 to 10V voltage output (FOV)

  LED display

It displays the parameters

Key locking and
function selection

It can lock the keys partially or completely and define the
function range of some keys so as to prevent mis-function.

Protection function

Motor short-circuit detection at power-on, output phase loss protection, over-current protection, over-voltage
protection, under voltage protection, overheat protection and overload protection.

Usage location

Indoor, avoid direct sunlight, dust, corrosive gas, combustible gas, oil fog, steam, drip or salt.

Altitude

Lower than 1000m(Lower the grades when using higher then 1000m)

Ambient temperature

－10℃~＋40℃(Lower the grades if the ambient temperature is between 40°C and 50°C)

Humidity

Less than 95%RH, without condensing

Vibration

Less than 5.9m/s2(0.6g)

Storage temperature

－20℃~＋60℃

IP protection

IP20