C-1 Cement paper tube making machine

Product Specification

C-1 Tube Making machine 

Technical Parameter

1. This equipment is only to produce A, M edge straight cut paper bags, film bags, 3 layers of sack paper + 1 PE film or 4 layer sack paper)

2. The paper rolling width: 0 ~ 1300 mm

3. The paper rolling diameter: 0 ~ 1300 mm

4. The paper width: 350 ~ 600 mm (A side bags cylinder)

5. The paper cut length: 600 ~ 1430 mm

6. The equipment design speed: 180 pcs / min (MAX) (calculated on bag length 900mm)

7. Total power equipment: 45KW

8. The paper stamping code: using photoelectric automatic counting: 50,100 for the counting unit

9. The equipment adopt mechanical drive, wheel need specifications

10. Electrical use industrial frequency converter, PLC, servo motor, photoelectric element, etc

11. Equipment size: about 30-33 M (length) * 2.5 M * 2.0 M (width) (high)

12. The capsular bag should also increase the bonding mechanism, suitable adhesive institutions, and eager to function

Equipment functional description

1. 4 Color Printing Machine :

1. Printing Width : 0-1460mm
2. Printing Length : 660-1430mm
3. Adjustment : Registered in running machine, no need stop.
4. Using flexible letterpress printing resin version
5. Printing precision can reach more than 35 line
6. Tinted accuracy within 1 mm
7. ink roller automatically during a break in the ink
8. When stop ink roller automatically from the plate roller

1. Paper Frame

1. The paper frame size is 1500 mm
2. gassing axis with a standard 3 "(75 mm)
3. paper roll can be fast clamping positioning, easy to change
4. paper roll can be adjusted axial, positioning, don't drift, intuitive
5. use a magnetic particle brake (may change according to customer's request)
6. to adopt passive
7.  

1. Hierarchical components

Mainly is to put the paper on the shelf each layer of paper after delamination roller separate, preparing for entering the next working step.

1. Correction institutions

Main is to be able to make the layers of paper cut into the ladder in a certain position, make the cutter ladder steady job, make qualified bags cylinder.When a layer of paper edge position deviation in set, correction institutions detection signal feedback to the host, and start the correction function, make the paper edge back in situ;

1. Auxiliary traction

Auxiliary traction is for each layer of paper drawing to provide middle power, reduce overall stretching, can let the straight cutting or ladder cutting stability.A kind of special device installed in front of the auxiliary traction (bag tube meet the requirements of ventilation rate).Auxiliary traction on the roll printing layer is equipped with manual adjustments S roll.

1. Ladder cutting institutions

Ladder cutting is cut the layers of paper into the state of the dotted line.Ladder cutting with special reducer, ladder knife origin point sensors.Place roll stability of printing paper, reduce the vibration and noise of the paper roll to improve cutting ability and stability of the bags, and at the same time can make the virtual cutting, more accurate, equipped with manual lubrication pump at the same time, reduce the gear wear and tear

1. Lateral dispensing mechanism

Transverse dispensing institutions including the three groups (or four) glue system of independent, glue adopts the combination of motor drive, reduce noise.The gluing quantity can be adjust, glue roller, recursive rubber roller adopts eccentric shaft sleeve can be changed in accordance with the different glue on the rubber roller and rubber roller clearance.Between each plastic box and plastic box there are automatic reflow and automatic for plastic pipes.Transverse dispensing with cut ladder Shared servo system, closed loop control.Using differential online adjusting position of transverse point glue, can make the dispensing in straight cut or cut ladder on both sides of any position

1. formed mechanism

Molding paper frame use tube forming components, type A, bag is designed for the A bag of cylinder.Simple and easy, and can very convenient to use a function

1. Snap institutions

Is mainly composed of the main traction wheel, signal, breaking mechanism, straight cut, cut/break frequency conversion system, etc.Bag drum break of traction, ladder, straight cut bag sliced function.After giving the main traction motor electrical system signal, motor drive the traction wheel and signal action together, annunciator work began to count, sensor signal acquisition.The useful signal transmission to the main control area and control area, comparing the set data to guide servo motor start work, continuous work cycle

1. Arrangement and stamping INS

Arrangement, stamping code institutions by the arrangement of institutions, fast out of the bag of institutions and organizations.In traction straight to the counter, the accumulation of data out of the bag, and arranged in an orderly arrangement, available for inspection the quality of the bags cylinder, the counter is set in the main control area is 25, 50, 100 to count for the unit, bag cylinder for the 25, 50, 100.

Machine Drawing