Truck TACHO tachograph programmer

Product Specification

Truck TACHO tachograph programmer

This tool no depends to truck
Only depend to tacho
Tacho install in truck
And this tool support all tachoo
So support all truck

Truck Tacho is designed for verification, calibration and configuration of control devices (tachograph) when installed on vehicles. 
The device allows you to define the W figure determination on measuring track or rolling road, K figure measure, can be used as speed simulator for the tachograph when checking the speedometer and odometer.

Truck Tacho calibrates and programs all analogue and digital tachographs

Supports IMS (Independent Motion Signal / Second speed signal) parameters on DTCO 2.0, SE5000 Exakt Duo and EFAS-4.

Supports ‘VDO counter’ parameter on DTCO 2.0

Kit included:

Truck tacho

6 Cables for digital tacho

For more information about this use manual, please contact with us to get this. 

Tachograph programmer JIUTACHO - User manual – V2.00 r07

1. Introduction
1.1. What is a tachograph?
Basically, a tachograph is a device that measures and records the speed and distance driven by a vehicle.
The data are recorded in the form of graphics on a paper disk.
The new digital tachographs record those data on its embedded memory and also on the smartcard of the
driver.

2.1 Technical specifications
- Graphic FSTF LCD Display:
100 x 32 px (4 lines x 20 char) - White LED backlight
- Size: 150 x 100 x45 mm
- Supply voltage: 9 to 30 VDC
- Supply current: 12mA
- Case: green-blue ABS (IP40)
- Operating temp: -20…+70°C


Tachograph programmer JIUTACHO - User manual – V2.00 r07 (9/01/2014)

2.2. Keyboard
- Alternate function keys 'F1', 'F2' & 'F3' are active when a function in
inverted video appears on the bottom line of the display.
Trac k l eng th

MODI FY
OK
F1= MODIFY, F3=OK
- Alernate function key '↑' & '↓' are used for example to navigate the
menus.
- Alernate function key '←' & '→' are used to select the digit in some
parameters.
- 'Ent' (=Enter) is used to select a function or enter a value.
- 'Esc' key is used to go back in the menu, leave a function, to erase
the last digit entered and to switch the programmer ON & OFF when
powered by the battery.
3. Operation
3.1. Power supply and tachograph type detection
For all tachograph types, except for the K13xx/1318 and the FTCO1319, the programmer is powered by the
tachograph itself. An automatic tachograph type detection is executed on power ON, so don't switch the
programmer ON, simply connect it to the tachograph with the appropriate cable. The programmer will switch
ON and detect the tachograph type.
In the case of the K13xx/1318 and the FTCO1319, switch the programmer ON pressing the 'I/O' key.
If the FTCO1319 is connected, the programmer will detect it.
To switch the programmer OFF, press and hold the 'I/O' key.
If no tachograph is detected, the K13xx/1318 will be selected by default.
On power ON, the programmer will display the product information (Software version, Serial number, etc...),
then the menu for the tachograph type detected.
3.2. Menu trees
The functions available in the main menu depend on tachograph model detected (or selected manually).
The tachograph model appears on the top line.
3.2.1. KTCO 13xx/1318
KTCO 13xx/1318
1.Measure W
1.Manual
2.Photo sensor
2.Measure K
3.Speed test
1.Manual
2.Automatic
4.Odometer test
5.Clock test
6.Select Tacho.
7.Product info.
8.Language.
3.2.2. MTCO 1324/1390
MTCO 1324/1390
1.Measure W
1.Manual
2.Photo sensor
1.K Factor
2.Odometer
3.Instal. Date
4.Calibr. Date
5.Time & Date
6.O/P shaft
7.Service delay
8.CAN priority
9.Binary code
10.Product Code
11.VIN
12.N-RPM Factor
13.L-Tyre
14.Serial number
15.Maximum speed (1390 only)
1.Manual
2.Automatic
2.Parameters
3.Speed test
4.Odometer test
5.Erase DTCS
6.Sensor pairing
7.Clock test
8.Select Tacho.
9.Product info.
10.Language.

3.2.3. Motomet.EGK100
Motomet.EGK100
1.Measure W
1.Manual
2.Photo sensor
1.K Factor
2.Kn
3.U1
4.U2
5.U3
1.Manual
2.Automatic

2.Parameters
3.Speed test
4.Odometer test
5.Select Tacho.
6.Product info.
7.Language.