10.1 Inch 1280x800 Lcd 40 Pins Lvds BP101WX1-206 330 Nits

Product Specification

10.1 Inch 1280x800 Lcd 40 Pins Lvds BP101WX1-206 330 Nits
 
General Description:

BP101WX1-206 is a 10.1 inch LCD module product introduced by BOE Technology Group Co.,LTD which adopts A-SI TFT-LCD technology. The display resolution is 1280x800,the aspect ratio is 16:10(width:height), and the pixels are arranged in RGB vertical strips. The size of the display area is 216.96x135.6mm, the visual size is 220.46x139.25mm, and the appearance size is 228.6x149.2x4.59mm. Surface treatment is mirror surface (Haze 0%), Hard coating(3H), anti-reflection treatment, product net weight 150g(Max). In terms of backlight, this product uses WLED luminous side-in light source (bottom), the service life of light source is 15K hours, including LED driver. LVDS signal interface,40 pins in total, with terminal connectin, drive screen voltage of 3.3V. Its typical vertical refresh rate FV is 60HZ. The operating temperature ranges from 0°C to 50°C and the storage temperature ranges from -20 °C to 60°C.This model is recommended for tablets.

 
Features:

• 1 Channel LVDS Interface with 1 pixel / clock
• Thin and light weight
• Display 16.7M colors (Hi FRC)
• High luminance and contrast ratio, low reflection and wide viewing angle
• DE (Data Enable) signal mode
• 3.3V for Logic Power and 3.7V for LED Back Light Power
• RoHS Compliant

Specifications:
 

 
Electrical Specifications:
 

Notes: 1.The supply voltage is measured and specified at the interface connector of LCM.The current draw and power consumption specified is for 3.7V at 25C Max value at White Pattern. 2.Calculated value for reference(VLED X ILED) 3.CTF of Power Supply Current:PD/PBL.

Optical Specification:

Notes :

           1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing angles are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to the optical axis which is normal to the LCD surface.

           2. Contrast measurements shall be made at viewing angle of Θ= 0 and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state .  Luminance Contrast Ratio (CR) is defined mathematically.

           3. Center Luminance of white is defined as luminance values of 5point average across the LCD surface. Luminance shall be measured with all pixels in the view field set first to white. This measurement shall be taken at the locations for a total of the measurements per display, the LED current is set at 20mA.

           4. The White luminance uniformity on LCD surface is then expressed as : ΔY = Minimum Luminance of 5 (13)points / Maximum Luminance of 5(13).

           5. The color chromaticity coordinates specified in Table 5 shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel.

           6. The electro-optical response time measurements shall be made by switching the “data” input signal ON and OFF. The times needed for the luminance to change from 10% to 90% is Tr, and 90% to 10% is Td.

           7. Cross-Talk of one area of the LCD surface by another shall be measured by comparing the luminance (YA) of a 25mm diameter area, with all display pixels set to a gray level, to the luminance (YB) of that same area when any adjacent area is driven dark.

Interface Connection:

The electronics interface connector is 20455-040E-12.

Dimensional Requirements: