Perfect International Instruments Co., Ltd
| Payment Terms | T/T, L/C, Western Union |
| Supply Ability | 300 sets per month |
| Delivery Time | 3 working days after confirm order |
| Packaging Details | packaged in paper box |
| Run-up segment | 100mm |
| Weight | 500g |
| Rolling ball | 29 pieces,not including No.1, No.27, No.31 |
| Design Standards | GB/T 4852 |
| Brand Name | POOTAB |
| Model Number | PT-6030 |
| Certification | ISO,CE,SGS |
| Place of Origin | Dongguan,Guangdong,China |
View Detail Information
Explore similar products
SGS Touch Screen 122m/Min Adhesion Testing Machine
Temperature Control Adhesion Testing Machine , Oven Type Tape Retentivity Tester
8 Groups Adhesive Tape Testing Machine Holding Force Retentivity Tester
PT-6030 Adhesion Testing Machine with 29 ball
Product Specification
| Payment Terms | T/T, L/C, Western Union | Supply Ability | 300 sets per month |
| Delivery Time | 3 working days after confirm order | Packaging Details | packaged in paper box |
| Run-up segment | 100mm | Weight | 500g |
| Rolling ball | 29 pieces,not including No.1, No.27, No.31 | Design Standards | GB/T 4852 |
| Brand Name | POOTAB | Model Number | PT-6030 |
| Certification | ISO,CE,SGS | Place of Origin | Dongguan,Guangdong,China |
| High Light | CNS11888 rolling ball tack tester ，100mm rolling ball tack tester ，100mm adhesive testing equipment | ||
Initial Tack Tester Rolling Ball CNS11888 Adhesion Test
Definition of primary tack :
Initial Tack: the adhesion of the adhesive tape to an object when the adhesive surface is temporarily contacted with minute pressure between the object and the pressure-sensitive adhesive tape.
Introduction: PT-6030 tape initial tack tester is an instrument for testing the initial tack of pressure-sensitive adhesive tapes and products similar to pressure-sensitive adhesive tapes. Its various technical indicators are in line with the provisions of GB/T 4852-1984. Its principle is to roll a rolling ball over the sticky surface of the adhesive tape lying flat on an inclined plate, and evaluate its initial tack according to the maximum number (size) of the sticky surface that can be stuck by a specified length of the sticky surface.
Equipment spec.:
Rolling Balls spec.: (Noted:According to(GB/T4852-2002), a set balls including 29 pieces,exclude 1/32,27/32,31/32)
| No | Dia(mm) | No | Dia(mm) | No | Dia(mm) | No | Dia(mm) |
| 1 | 0.794 | 9 | 7.144 | 17 | 13.494 | 25 | 19.844 |
| 2 | 1.558 | 10 | 7.938 | 18 | 14.288 | 26 | 20.638 |
| 3 | 2.381 | 11 | 8.731 | 19 | 15.081 | 27 | 21.431 |
| 4 | 3.175 | 12 | 9.525 | 20 | 15.875 | 28 | 22.225 |
| 5 | 3.969 | 13 | 10.319 | 21 | 16.669 | 29 | 23.019 |
| 6 | 4.762 | 14 | 11.112 | 22 | 17.462 | 30 | 23.812 |
| 7 | 5.556 | 15 | 11.906 | 23 | 18.256 | 31 | 24.606 |
| 8 | 6.350 | 16 | 12.70 | 24 | 19.050 | 32 | 25.4 |
Operation Steps Of Roll Ball Tack Testing :
1. Place the machine on a stable table so that the pointer is aligned with the zero line of the Angle plate; Adjust the floor to level the work surface.
2. Then adjust the work surface to the Angle required by the test, generally 30°.
3. Fix the adhesive tape (test strip) to be tested on the working table (100 mm below the center of the ball is the running section), and fix the bottom edge of the test strip extending to the steel ball box with 500g weight, so that the test strip is naturally flat under a heavy weight.
S1. The test slice should be at least 4 pieces with a width (10 ~ 80 mm) and a length of about 250mm. If the elongation of the test slice is large, the test slice should be left for a period of time before the test.
S2. For the run-up section, the transparent polyester film of electrical appliances with a thickness of 25 m and a length of more than 100 mm is pasted on the adhesive surface of > at the designated position of the test piece, with a length of 100 mm.
S3.100mm run-up is adjusted by adjusting the bolts on the machine and corresponding positions of the rolling balls with different ball sizes.
4. Pre-select maximum roll
Adjust the starting position of the ball, select balls with different ball Numbers, and repeat the systematic operation of ball cleaning and rolling.Pick the largest of the primary balls that are stopped in the measurement interval (the ball does not move for more than 5 seconds).Take the largest ball selected from the same test piece and the two balls with the ball number and its adjacent size, and test them on the same sample once each to confirm the ball with the largest ball number.(rolling the test on the same chip several times before picking the largest ball is acceptable, but it cannot be used as official test data.)
5. Formal testing
Take three samples and roll the ball on each of them with the maximum ball number selected.If a sample cannot stick the ball, the smaller ball can be used for a test. If it still cannot stick, the test shall be retested according to the steps of "pre-selected maximum ball" and "formal test".
6. Test results
The test results are expressed as the median ball number (ball diameter) of the ball test results of the three samples in the formal test.
Rollong Ball Tack Tester Photo :
Company Details
Business Type:
Manufacturer
Year Established:
2003
Total Annual:
5 Million-10 Million
Ecer Certification：
Verified Supplier
Perfect International Instruments Co.,Ltd, the excellent supplier of global testing machine and related services, was founded in 1997 ,Taiwan .Then, Dongguan factory was founded in 2003. It has been providing quality improvement solutions for rubber, plastics, footwear, food, daily chemica... Perfect International Instruments Co.,Ltd, the excellent supplier of global testing machine and related services, was founded in 1997 ,Taiwan .Then, Dongguan factory was founded in 2003. It has been providing quality improvement solutions for rubber, plastics, footwear, food, daily chemica...
Get in touch with us
Leave a Message, we will call you back quickly!