Otal Power About 9kw Temperature Humidity Chamber Jd-8002 Laboratory Dedicated

Product Specification

Otal Power About 9kw Temperature Humidity Chamber Jd-8002 Laboratory Dedicated Oven​

Product Usage:

This oven is designed for laboratory, laboratory, hospital and various electronic product baking, epoxy resin hand baking, electrical pouring, and baking of various magnetic accessories, baking and drying at the specified temperature. , disinfection, heat treatment aging and other heating applications.

 
Features:

Energy-saving: After the temperature rises to the set temperature, the PID intelligent thermostat automatically enters the energy-saving state to turn off most of the heating wire power supply, effectively controlling
The power consumption is reduced; and the longer the start-up time, the more energy-saving is, which is about one-tenth of the energy consumption of the same industry.
(The test result is: the energy loss can be reduced by about 80%~90% when entering the energy saving stage)
 Heating method: PID+S.S.R is more stable
Circulation mode: forced horizontal circulation air supply
Safety device: ultra high temperature protection, overload automatic power off system, safer
Control mode: intelligent controller PID automatic calculation, compensation, calibration More precise
The controller is located above the machine, single door
The inner material is #SUS 316 stainless steel plate, and the outer material is made of high quality 304 stainless steel matte finish.
The insulation material is imported high-density glass rock wool, which has good heat insulation and maximum temperature insulation. The anti-tight and tight material is high temperature resistant rubber, which can withstand high temperature of 600 degrees for a long time.

 
Temperature Control System

The temperature control is PID micro-automatic calculation of PV/SV simultaneous display. It can set any temperature condition within the temperature range according to actual needs, and can ensure the accuracy of its temperature control through the PID parameter setting in the table. The system of the belt self-calculated to obtain appropriate temperature control parameters.

The temperature input force CA(K) TYPE output is 12V.
The current controller is a SSR contactless relay that maintains high current stability.
The heating material is imported nickel-cadmium alloy heating wire, which is non-polluting and has a long service life.

 
Air supply system

Forced horizontal air supply circulation, the wind source is driven by the circulating motor to drive the wind wheel through the electric heater, and the hot air is sent from the air duct to the inside of the oven, and the hot air is sucked into the air duct as a source to be recirculated and heated, thereby reducing energy loss and Ensure the temperature uniformity inside the box, when the door opening and closing action causes disturbance, the air circulation system can quickly return to the operating state temperature value.

The motor is imported from Taiwan for long-axis high temperature type, and the power is 1HP50Hz.
The fan is a multi-blade turbine type with high strength and an adjustable guide air deflector for smoother circulation of the wind.
 

safety protection

Ultra high temperature protection, no fuse switch, porcelain fuse, motor overload protection.
Timer 9999 seconds ~ 9999 hours (H.M.S switch and decimal point position setting)
When the temperature is up, the time is cut off, the heating is stopped and the alarm is stopped.
 

Technical indicators

Heating system and its working principle

Heating system Built-in nickel-chromium alloy heater, non-polluting and long service life;

 
Temperature cycling system

Temperature cycle mode Forced circulation ventilation, balance thermostat (BTC). The method not only refers to the continuous operation of the circulation system, the control system controls the output of the heater according to the result of the PID automatic calculation output according to the set temperature point, and finally achieves a dynamic balance.
 

control system

Temperature measurement PT100
The temperature control is PID PID automatic calculation PV/SV simultaneous display, the required temperature can be freely set according to the individual's will within the allowable range of the machine temperature, and the accuracy of temperature control can be ensured by the PID parameter setting in the table. It can also be calculated by the system itself to calculate the appropriate temperature control parameters.
The temperature input force CA(K) TYPE output is 8V.