380V 0.8m -1.8mm 2.2kw Welding Wire Machine For Wooden Screws Electric Lead

Product Specification

380V 0.8m -1.8mm 2.2kw Welding Wire machine for woodenscrews electric lead

After- sales service

1. Guarantee time: one year since machine was at buyer's factory but within 18 months against B/L date.
2. Within guarantee time, if any components are broken under normal condition, we can change for free.
3. We can send our best technician to buyer's factory for installation, debugging and training.
4. Complete installation instructions, circuit diagram, manual operations and machine layout.
5. Timely reply for your machine questions, 24 hours support service.

Eight peeling wheel,

• material: ZG45 steel, hardness of HRC50, Wheel
• inner diameter Ф 115 --- Ф 120mm.
• Wheel service life of 6000 hours. After
• peeling ,the wire through period of tapered hole, use wire clean ball strongly wipe the
• surface of wire rod, and does not damage
• the wire surface, reduce the waste into the electrolytic pickling tank, ensure the
• effect of pickling, facilitate drawing; By pressure cold water irrigation and block and
• impurities, rust on the surface of the wire rod export high-pressure gas blowing
• device, reduce by wire out of the water.

Safe system:

① start up limit function of opening up the protection cover, unresetting fixed-length,

insufficient air pressure, unresetting brake(when open up the

protection cover, the equipment is in inching condition

② automatic shutdown when line broken, and assure wire not be broken；

③ pull rope siwtch can realize crash stop conviently and fast

④ main operation desk, pay off and take up machine have mushroom emergency

push button switch, emergency stop time consuming ≤5S (quick stop≤15S,normal

stop ≤30S

Lighting system:

wire drawing machine design with low voltage 24 v LED lighting system, is

advantageous for the cloudy day or night can clearly see the wire drawing the

status quo, lighting switch is located in the touch screen, easy to open or close

at any time

3 Fine wire drawing production line

LZ8/400 Straight line wire drawing machine

I-Spool Pay-off Rotary Pay-Off

The advantages and disadvantages of two kinds of take-up machine

The advantages of I-Spool take-up machine:I-Spool steel wire into Fine wire drawing production line, the pay-off machine 100% not disorderly silk；

The advantages of Trunk-type Unloading Machine:steel wire Good cooling,When Fine wire drawing ,wire break is very little,so Good quality of welding wire,Don't need a lot of Ф800mm I-Spool.Please select a user.

Equipment composition:

(1) Ф800mm I-spool pay-off machine or rotary pay-off machine

(2) LZ8 /400strainght line wiredrawing machine(or seven joint combination)

(3) Tension stand

(4) Cleaning: water + machinery scrubbing+ sprinkling+ high pressure blowing

(5) Ф630mmI-Spool take-up machine

(6) Work station:man-machine interface control touch screen

(7) complete set electic control cabinet

3.3 Main technical parameters and main points:

(1) Maximum enter-wire strength≤1000MPa

(2) Maximum enter-wire diameter:Ф2.35mm

(3) Minimum enter-wire diameter:Ф0.8mm

(4) Maximum compression rate:88%

(5) Maximum drawing speed:20 m/s Normal drawing speed:15--18m/s

(6) Gas consumption and air pressure:1.0 m3/h Air pressure≥0.6Mpa

(7) Water consumption and pressure:5 m3/h Water pressure≥0.2Mpa

(8) Motor: drawing and take-up all adopt 11KW 50HZ AC frequency conversion motor

(9) Transmissions type:

① drive by Grade-1 or Grade-2 poweful banded wedge V-belt which has high efficiency

② each head has electromagnetic valve to control high efficiency aerobraking

(10) Tensionmachine :

① Tension wheel diameter:≥Ф320mm

② tension wheel material:it is the first who use aluminum alloy as material in

domestic, spray ceramic on working surface; the hardness is ≧HRC60 ,make it

has fine brightness and abrasion resistance, not only protect the wire not to be

hurt,but also ensure its useful life mre than two years.

(11) degreasing machine: machinery scrubbing, multiple Segment cone shaped hole, high pressure sprinkle washing ( sewage draining exit is designed on th

bottom of circulation pool )； repeating wrapping wheel material is ductile cast iron

(dia. Ф320)； machine body is 2.2m long.

Other and Control System :the same with wire drawing machineLZ6/560

№1. Ф800mm I-Spool pay-off machine

1. pneumatic clamping h-wheel, the top (back)

2. wheel support: double cone duplicate (no-shaft type),

3. the brake: pneumatic brake

4. speed control: mechanical damping pay-off

5. safety device: safety shield door

№2.  rotary pay-off machine

Will be filled with steel wire of the wire frame in the middle of the shelf (like in the picture), extract steel wire drawing machine power, the shelf with pneumatic damping and emergency brake, to ensure that the pay-off and the wire drawing machine's first block always in sync.