440C Stainless Steel Sheet Metal Strips 0.4-6.0mm Cold Rolled UNS S44004

440C Stainless Steel Strip Thickness 0.4 - 6.0mm Cold Rolled SS Strip UNS S44004

STAINLESS STEEL 440 STRIP GENERAL PROPERTIES:

Stainless steels 440 Strips are high-alloy steels which have high corrosion resistance compared to other steels due to the presence of large amounts of chromium. Based on their crystalline structure, they are divided into three types such as ferritic, austenitic, and martensitic steels. Another group of stainless steels are precipitation-hardened steels. They are a combination of martensitic and austenitic steels. Grade 440C stainless steel strip is a high carbon martensitic stainless steel. It has high strength, moderate corrosion resistance, and good hardness and wear resistance. Grade 440C strip is capable of attaining, after heat treatment, the highest strength, hardness and wear resistance of all the stainless alloys. Its very high carbon content is responsible for these characteristics, which make 440C particularly suited to such applications as ball bearings and valve parts.

Our Stainless steel 440 strips capabilities include:

• Stainless steel 440 strips Annealed & Precision
• Stainless steel 440 strips thickness-0.1mm to 6.00mm
• Stainless steel 440 strips width-2.5mm to 1320mm (slit to close tolerances)

Our Stainless steel 440 Cold rolled mill finish strips such as:

• Stainless steel 440 strips 2D - cold rolled, heat treated, pickled.
• Stainless steel 440 strips 2B - cold rolled, heat treated, pickled, skin passed on bright rolls.
• Stainless steel 440 strips 2R(BA) - cold rolled, bright annealed
• Stainless steel 440 strips HR - hot rolled, annealed

STAINLESS STEEL 440 STRIP APPLICATIONS:

Typical applications include:

• Rolling element bearings
• Valve seats
• High quality knife blades
• Surgical instruments
• Chisels

STAINLESS STEEL 440 STRIP CORROSION RESISTANCE:

Good resistance to the atmosphere, fresh water, foods, alkalies and mild acids. Best resistance in the hardened and tempered and passivated condition. A smooth polished surface also assists.

The corrosion resistance of grade 440C approximates that of grade 304 in many environments.

STAINLESS STEEL 440 STRIP HEAT RESISTANCE:

Not recommended for use in temperatures above the relevant tempering temperature, because of reduction in mechanical properties by over-tempering.

STAINLESS STEEL 440 STRIP HEAT TREATMENT:

Annealing – Full anneal – 850-900°C, slow furnace cool to about 600°C and then air cool. Sub-critical Annealing – 735-785°C and slow furnace cool.

Hardening – Heat to 1010-1065°C, followed by quenching in warm oil or air. Oil quenching is necessary for heavy sections. Immediately temper at 150-370°C to obtain a wide variety of hardness values and mechanical properties as indicated in the accompanying table.

Tempering in the range 425-565°C is to be avoided because of reduced impact resistance and corrosion resistance. Tempering in the range 590-675°C results in lower hardness (the product become machinable) and high impact resistance.

STAINLESS STEEL 440 STRIP WELDING:

If welding is necessary pre-heat at 250°C and follow welding with a full anneal. Grade 420 filler will give a high hardness weld (although not as high as the 440C), but 309 or 310 will produce soft welds with higher ductility.

STAINLESS STEEL 440 STRIP MACHINING:

In the annealed condition this grade is relatively easily machined; approximately the same as for high speed steel. Chips are tough and stringy so chip breakers are important. If these grades are hardened machining becomes more difficult and probably impossible.