Oil Immersion Test Equipment IEC 62368-1 For The Oil Resistance Test Of Enameled

Product Specification

Oil Immersion Test Equipment IEC 62368-1 For The Oil Resistance Test Of Enameled Wires

Product Information:

This oil immersion test equipment complies with ASTM D471-98, IEC 62368-1: 2018, Section Y.4.5, etc.
The tester is suitable for testing the oil resistance of rubber, plastic enameled wire or insulator.
Test method: Immerse the specimen in hot oil, then remove the specimen and test its tensile strength. If the test piece is enameled wire, check the paint film quality.

Features:

Oil immersion test equipment, also known as oil bath testers or oil immersion tanks, is specialized equipment used to subject electrical components or equipment to immersion in oil for testing purposes. The oil immersion test is performed to evaluate the insulation properties, dielectric strength, and overall reliability of the test specimen in an oil-filled environment. Here are the key features and functions typically associated with oil immersion test equipment:

Immersion Tank: The oil immersion test equipment consists of a tank or container that is specifically designed to hold the oil and accommodate the test specimen. The tank is typically made of non-conductive materials, such as plastic or stainless steel, to prevent interference with the test.

Oil Medium: The equipment requires a suitable insulating oil, such as mineral oil or silicone oil, to fill the immersion tank. The choice of oil depends on the specific testing requirements and the standards being followed. The oil serves as both the dielectric medium and the cooling medium during the test.

Temperature Control: The oil immersion test equipment incorporates a temperature control system to regulate the temperature of the oil during testing. This ensures that the oil remains within the desired temperature range specified for the test. Temperature control may involve heating elements, cooling systems, and temperature sensors to monitor and adjust the oil temperature accordingly.

Electrical Connections: The equipment includes electrical connections or terminals within the immersion tank to allow for the energization of the test specimen during testing. These connections enable the application of electrical voltages or currents to evaluate the insulation properties and dielectric strength of the specimen under oil immersion.

Test Duration Control: The equipment provides control over the duration of the immersion test. Test duration can be adjusted based on the testing standards or specific requirements. Typical test durations can range from a few minutes to several hours, depending on the test objectives.

Safety Features: Safety measures are integrated into oil immersion test equipment to protect the operators and prevent accidents. These features may include electrical isolation, grounding provisions, leakage detection systems, and emergency shut-off mechanisms to ensure safe operation of the equipment.

Compliance with Standards: Oil immersion test equipment is designed to comply with industry standards and regulations, such as those set by IEC (International Electrotechnical Commission) or ASTM (American Society for Testing and Materials). Compliance ensures that the testing process is conducted in a standardized and reliable manner, allowing for accurate assessment and comparison of the test results.

Oil immersion test equipment is commonly used in electrical and electronics industries to assess the insulation properties and dielectric strength of various components, such as transformers, insulators, cables, and electrical connectors. The test helps manufacturers ensure the performance and reliability of their products under submerged or oil-filled conditions, providing critical information for design optimization and quality control.

Instrument composition:

1. Dumbbell test cup (stainless steel): 6 pieces, height 300mm (or custom).
2. Test cup cover material: six pieces of corrosion and temperature resistant advanced rubber (tight plug) or six pieces of aluminum plug (loose plug).
3. In the workshop (space for holding the test cup for insulation and heating): 320 x 300 x 350 mm, stainless steel.
4. With sample isolation and suspension device (6 pieces, each corresponding to a test cup, each device can be suspended 3 dumbbells).
5. Built-in hybrid cycle mode, hybrid power: 40 W.

Temperature control and insulation system:

1. Imported intelligent PID constant temperature and high precision k-type thermocouple transducer.
2. Heater: electromagnetic heater, power: 3000 W
3. Temperature range: room temperature: + 20 °C ~ 300 °C, instrument display accuracy: 0.1 °C, oil temperature uniformity: ± 1 °C
4. With super high temperature protection function, can automatically cut off and stop heating after over temperature, effectively protect the safety of equipment.
5. Automatic power off when oil level is insufficient; High temperature splash protection of test oil
6. Volume: 400 X 530 X 550mm, Inner and Outer Box: Stainless Steel
7. Time Set: 999.99 H / M / S