MINGCHENG GROUP LIMITED
| Payment Terms | L/C, , T/T, Western Union, PayPal , |
| Supply Ability | 4000kgs/day |
| Delivery Time | about 3-5 working days after payment |
| Packaging Details | 1kg/can , 5kg/can , 10kg/drum , 20kg/drum , 25kg/drum , 200kg/drum |
| Product Name | Silicone in primary forms |
| HS Code | 39100000 |
| Color | Grey |
| Viscosity | 4500 cps |
| Mixing ratio | 1:1 |
| Working time | 60-120mins |
| Hardness | 56 shore A |
| Dielectric breakdown voltage kv/mm 25°C | ≥20 |
| Thermal conductivity（W/m·K） | ≥0.6 |
| Curing time | room temperature cure or heat cure |
| Thermal Conductivity | 0.62 |
| Brand Name | MC SILICONE |
| Model Number | MCSIL-E160 |
| Certification | MSDS |
| Place of Origin | China |
View Detail Information
Explore similar products
Good Flowability Two-Part Silicone Potting Compound And Encapsulants 160
Good Flowability Flame Resistance Waterproof 1 To 1 Mix Silicone Encapsulation &
Black Liquid Silicone Encapsulants Potting Compound Gel For LED / Solar Cells
Grey Liquid Silicone Potting Compound For Pcb Encapsulants
Product Specification
| Payment Terms | L/C, , T/T, Western Union, PayPal , | Supply Ability | 4000kgs/day |
| Delivery Time | about 3-5 working days after payment | Packaging Details | 1kg/can , 5kg/can , 10kg/drum , 20kg/drum , 25kg/drum , 200kg/drum |
| Product Name | Silicone in primary forms | HS Code | 39100000 |
| Color | Grey | Viscosity | 4500 cps |
| Mixing ratio | 1:1 | Working time | 60-120mins |
| Hardness | 56 shore A | Dielectric breakdown voltage kv/mm 25°C | ≥20 |
| Thermal conductivity（W/m·K） | ≥0.6 | Curing time | room temperature cure or heat cure |
| Thermal Conductivity | 0.62 | Brand Name | MC SILICONE |
| Model Number | MCSIL-E160 | Certification | MSDS |
| Place of Origin | China | ||
| High Light | Silicone Potting Compound For Electronics ，Thermal Conductive Silicone Potting Compound ，2 Part Silicone Encapsulants | ||
Product Description
Silicone potting compounds and encapsulants provide a flexible, protective barrier or enclosure against a variety of environmental factors for electronic circuits and systems. These silicones are used when a deep section cure is required and prevent, debris, heat shock and vibration from damaging the electronics.
In addition to protecting electronic components, silicone potting compounds and encapsulants are used for other functionalities that may be required such as thermal transfer and light emission.
Features:
· Two-component addition type silicone potting compound.
· Mix ratio is 1:1
· Low hardening shrinkage.
· Excellent high temperature electrical insulation and high stability.
· Good waterproof and moisture-proof.
· Excellent flame retardant.
Applications:
· Automotive electronics, modules.
· LED power driver module.
· Solar module junction box.
· Electric vehicle charging column module.
· Lithium battery and capacitor bank.
· Magnetic induction coil
· power inverters
Technical datasheet of Electronic Potting Silicone Compound& Encapsulates
| Item No. | RTV160 |
| Before curing | |
| Appearance | A: brick red B: transparent |
| Viscosity (mPa.s 25°C) | 3000~6000 |
| Density (g/cm3 ) | 1.57±0.02 |
| Working life (min 25°C) | 30 |
| Curing time (hrs) | 24 |
| Heat-up at 100°C (min) | 10 |
| After curing | |
| Hardness (shore A) | 50~60 |
| Dielectric breakdown voltage kv/mm 25°C | ≥20 |
| Volume resistivity ohm*cm | 1*1015 |
| Tensile Strength Mpa | ≥0.6 |
| Thermal conductivity cm/°C | 0.525*10-3 |
| Working temperature °C | -30~200 |
Note: Mechanical and electrical performance data tested at 25°C 7 days after curing, relative humidity of 55%; all the tested data is average value.
PREPARING SURFACES
In applications requiring adhesion, priming will be required for many of the silicone encapsulants. For best results, the primer should be applied in a very thin, uniform coating and then wiped off after application. After application, it should be thoroughly cured prior to application of the silicone encapsulant.
PROCESSING/CURING
Thoroughly mixed silicone encapsulants may be poured/dispensed directly into the container in which it is to be cured. Care should be taken to minimize air entrapment. When practical, pouring/dispensing should be done under vacuum, particularly if the component being potted or encapsulated has many small voids. If this technique cannot be used, the unit should be evacuated after the silicone encapsulant has been poured/ dispensed. MC silicone encapsulants may be either room temperature (25 °C/77 °F) or heat cured.
Packaging of Electronic Potting Silicone Encapsulates
Packs are available in 20kg and 200kg per drum.
Storage & Transportation of Electronic Potting Silicone Encapsulates
USABLE LIFE AND STORAGE
Shelf life has 12 months after the production date.
Containers should be kept tightly closed and head or air space minimized. Partially filled containers should be purged with dry air or other gases, such as nitrogen. Exposure to moisture could reduce adhesion and cause bubbles to form.
Company Details
Business Type:
Manufacturer,Exporter,Seller
Year Established:
2010
Total Annual:
5000000-10000000
Employee Number:
50~80
Ecer Certification：
Verified Supplier
Mingcheng Group Limited was established in 2010 based in Dongguan,China, with brand MC Silicone for overseas market, dedicated to manufacturing and R&D of mold making and casting materials. Our professional approach to all our work, together with creative ideas and strong technical ... Mingcheng Group Limited was established in 2010 based in Dongguan,China, with brand MC Silicone for overseas market, dedicated to manufacturing and R&D of mold making and casting materials. Our professional approach to all our work, together with creative ideas and strong technical ...
Get in touch with us
Leave a Message, we will call you back quickly!