Steel Bar Straightening hydraulic press machine 100T Bending Force 900mm Stroke

Product Specification

Steel Bar Straightening hydraulic press machine 100T Bending Force 900mm Stroke

buy power press machine,hydraulic press, press machine,bending machine

Purpose:

this series of machine tools can be used for shaft, bearing and other similar calibration process.

It can also be used as an axle, a set of other parts of the compression and simple plate elements

stretching, molding, blanking and other processes.

This series of machine tools are operated with hands and feet, simple operation, low energy

consumption and low noise. According to the user's request to produce the series of various

tonnage variation machine tools.

 Hydraulic press machine troble analysis:

Hydraulic press is a forging equipment composed of main engine, hydraulic system and

electrical system. In the early 80 s last century, because of hydraulic press hydraulic system

adopts the control element, for large volume, low flow manual pipe valve structure, limit of

hydraulic press slider speed ascend, was widely seen as a forging industry to end products.

After more than 30 years, hydraulic presses have not been eliminated, but become an

indispensable equipment in the forging industry. One of the most important reasons is

technological innovation.

Hydraulic system is indispensable to hydraulic system. The function of hydraulic system is to

increase pressure by changing pressure. A complete hydraulic system consists of five parts:

power element, actuator, control element, auxiliary element (accessory) and hydraulic oil.

Hydraulic system is the key to ensure the normal operation of hydraulic press. The following

is the common fault prevention measure of hydraulic press.

1. The sound produced by the work of hydraulic press. First of all, we can work through hydraulic

press, whether listening to the hydraulic pump and hydraulic system of the noise is too big, relief

valve,sequence valve, pressure control components such as whether to have the screams, and

listen to the sound, the point at which the workbench hydraulic cylinder when reversing impact is

too large, whether to have hit the bottom of the cylinder piston, are there any impact on the reversing

valve reversing the phenomenon of end cover.

2. Through the detection of all parts of the hydraulic press. Through touch, touch the moving parts

of the allowed mold with the hand, and understand its working status:

(1) the vibration of the moving parts and pipes is handled by touching the vibration, and the cause

of the high frequency vibration should be checked.

(2) when the table is moving at a low speed, it can feel whether it is crawling or not.

(3), touch tightness, a hand touch block iron, micro switch and fastening screws, and other general tightness

of different people have different feelings, there must be a difference, but after repeated

practice, will eventually solve the problem. This approach is mainly aimed at experienced technician

s who are more experienced.

Work Environment :

Power Requirement: Three phase four wire, 380V, 50HZ ( as design accepted)

Installation Field: Clean, low dust

Maximum Temperature :40ºC

Minimum Temperature: -5ºC

Relative Temperature:55—85%

Height: less than 1000M

Optional touch screen terminals offer:

Data storage of mould(s) and manufacturing conditions.

Reduced mould replacement time and calibration, fabrication requirements.

Programmable memory for working conditions, displays pressure, stroke, spend data, etc;

one cycle process sequence.

Technical data:

Packing & shipping:

PVC film covered hydraulic press

Whole machine fixed in the container with steel rope,very safe

Wooden case or pallet or iron box

If have stock,can provide right now

If no stock,small machine delivery time 7-15days.Big machine delivery time 25-40days.

Can give destination port best price or cost to the customer factory

Our Service:

All machines have been tested by 48 hours before ship out.

All products have 2 year warranty.

Supported 24 hours online service. If any problems happen, our team will do our

best to solve the problems.

If any component is damaged during guarantee time. we can send the component to

the customer by DHL freely

Our Advantage:

MOQ: We can supply you the quantity you want.

OEM: We can produce the goods as per the customer requirement.

Service: We are much more concern for the on time delviery & quality

More information please contact us:

wxmachinery@163.com

WhatsApp:+86 13961729519

Skype: zouqicheng

QQ: 2308574039

 200T steel plate hydraulic press machine