CO2 Liquid Steam Brass Solenoid Valve Normally Closed High / Low Temperature

Product Specification

CO2 Liquid Steam Brass Solenoid Valve Normally Closed High / Low Temperature

Applicability

1 . The pipeline fluid must same as solenoid valve marked medium .

2 . Fluid temperature must be less than the marked temperature .

3 . If fluid is not high cleanliness , should be installed a filters in front of the solenoid valve , general solenoid valve is better claim to medium cleanness

4 . Pay attention to the orifice and port size ; usually only open and close two type ; Conditions permit , please install bypass pipe , easy maintenance ; When there is water drain to customize solenoid valve opening and closing time regulation .

5 . Pay attention to the environmental temperature on the influence of solenoid valve .

Reliability

Solenoid valve is divided into normally closed and normally open . General choose normally close , power on is open and power off is shut down ; But in the open for a long time and very short close time to choose the normally open type .

Security

1 . General solenoid valve is not waterproof , when needs waterproof model , we can be customized .

2 . Nominal pressure solenoid valve of the highest calibration must be more than the highest pressure in the pipeline , otherwise life will shorten or other unexpected circumstances .

Economy

There are a lot of solenoid valve can be common use , but on the basis of can satisfy the above three terms , should choose the most economical products.

B Series solenoid valve it is serialized products , large flow rate , good applicability . widely used in steam , oi and the other high & low temperqture linquid control

Adopted high temperature resistance seal material - PTFE ( which material import ) , when the meida passage the properties is good .

Coils type : high temperature resistance coil meanwile has the heat conduction protection .

Ensure the long life time and high reliability .

Main Technical Parameters

1 . 2 / 2 - Way solenoid valve , closed when de - energized , open when energized .

2 . Main material : body : forged brass , component : Stainless Steel

3 . Seal material : PTFE

4 . Ambient temp . : - 20 ~ 65 ℃

5 . Operating pressure : 0 . 0 ~ 50 . 0 kgf / cm ²

6 . Media temp . : - 100 ℃ ~ - 10 ℃   high temp . : 99 ℃ ~ 200 ℃

7 . Media : high temperature : steam , heat conducting oil and so on low temperature : n₂ , o₂ ,   co₂ 

attenation : under the naturature temperature , such as air , water and the other 

media , please choose the other economy & suitable solenoid valve .

8 . Voltage : AC24V / 110V / 240V / 230V 50 / 60 HZ  DC 12V / 24V

power consumption : AC27va ( 16 W ) DC 24W

Voltage tolerance : - 10 % ~ + 10 %

Coils type : w ( normally ) a = din standard , metallic housing

Safty series : class h heat resistance coil , ip 65

9 . Install : flow as the arrow , solenoid vertical and upright direction . if media has the eranule impurity , please install more than 60 mesh filter .

Large Diameter

Main Technical Parameters

1 . 2 / 2 - Way solenoid valve , Closed when de - energized , open when energized .

2 . Main material : body : forged brass  component : stainless steel 

3 . Seal Material : PTFE

4 . Ambiet Temp . : - 20 ~ 65 ℃

5 . Operating Pressure : 1 . 0 ~ 10 . 0 kgf / cm ² Max . : 15 . 0 kgf / cm ²

6 . Media Temp . : Low Temp . : - 100 ℃ ~ - 10 ℃  high Temp . : 99 ℃ ~ 185 ℃

7 . Media : high temperature steam , heat conducting oil and so on low temperature : N_{2 ,} O_{2 ,} CO₂

Attenation : Under the naturature temperature , such as air , water and the other media , please choose the other economy & suitable solenoid valve . 

8 . Voltage : AC24V / 110V / 240V / 230V /  50 / 60 HZ  DC12V / 24V

Power Consumption : AC27VA ( 16W ) DC24W

Voltage Tolerance : - 10 % ~ + 10 % 

Coil type : W ( Normal ) = Leed Wires A = DIN Standard , Metallic Housing

Safty Series : Class H Heat resistance coil , IP 65 

9 . Install : Flow as the arrow , solenoid , vertical and upright direction . if media has the granule impurity , please install more than 60 mesh filter .

FAQ                                                                                                                                                               

Q: How much is our minimum order quantity ?
A: Our minimun quantity is 1 Piece .

Q: Could you offer the free samples ?
A: Yeah, we could offer the free samples based on special customer.pre-production sample,production sample.

Q: What ' s your business scope ?
A: Our business scope is SMC type high quality cylinder , air source treatment , solenoid valve ,water valve,steam valve, mechnical valve ,foot valve,angle seat valve,anti-explosion valve,pluse vlave, pneumatic valve ,hydraulic ball valve,hydraulic ss ball valve,hydraulic check valve,hydraulic solenoid valve ,all type of coil,lubrication pump and parts,SS316 fitting,quick coupler , etc .

Q: What ' s your delivery date ?
A: It depends on the number of orders . Delivery date is 7 - 30 days .if small order,pls buy from our aliexpress shop, If you need emergency products , we can speed up the production of the first arrangement .

Q: What is the price of the product ?
A: Our prices are based on the size and type of material , if you can give me the information ,
then we can give you an estimated price is for reference only . We can do any size and any desgin .

Q: what types of products you can make ?
A: We can make many kinds of stainless steel materials and brass,aluminum . Valve / solenoid valve / electric valve / pneumatic valve and air cylinder products and so on .

Q: Do your company have specialized technical personnel ?
A: Design as your requirements,and have QC for make 100% inspection

Q: Can the product be made with our logo and brand ?
A: Yes , of course , we can make . we are OEM supplier for years and professional to make . But you need give us the authorization for work.

Why choose us                                                                                                                                              

1: Various style for each products and completely series pneumatic products .
2: Large stock for fast shipping .
3: High quality with competitive price .
4: Sample order & small quantity order is acceptable .
5: Customize according to your special request .
6: Provide free products information .
7: Reliable quality assured and active after-sell service
8: One year quality guarantee