Qingdao Huashida Machinery Co., Ltd.
| Payment Terms | L/C, D/A, D/P, T/T, Western Union, MoneyGram |
| Delivery Time | 10workdays |
| specific density | 0.935r/cm3 |
| tensile strengt | 38 Mpa |
| Elongation at break | 385% |
| water-intake rate | 0.05% |
| peel strength | >150N/cm |
| Brand Name | HUASHIDA |
| Certification | ISO9001 |
| Place of Origin | Qingdao，Shandong，China |
View Detail Information
Explore similar products
PE Heat Shrinkable Sleeve 2 Layers Anti Corrosive For Large Diameter Wastewater
Pipeline Joint Radiation Cross Linked Heat Shrinkable Sleeve 20 Mpa
Wraparound Heat Shrinkable Sleeve For 3PE Oil Gas Pipe Girth Weld Straight Joint
HDPE Plastic Heat Shrink Sleeve Tape For Oil And Gas Pipeline Joint
Product Specification
| Payment Terms | L/C, D/A, D/P, T/T, Western Union, MoneyGram | Delivery Time | 10workdays |
| specific density | 0.935r/cm3 | tensile strengt | 38 Mpa |
| Elongation at break | 385% | water-intake rate | 0.05% |
| peel strength | >150N/cm | Brand Name | HUASHIDA |
| Certification | ISO9001 | Place of Origin | Qingdao，Shandong，China |
| High Light | pipe coating joint 3pe heat shrink ，3pe Coating PE Pipe Wrap Sleeves ，PE Pipe Wrap Around Sleeve 38 Mpa | ||
3pe Coating pipe Joints Heat shrinkable sleeve,PE Pipe Wrap Around Sleeve
HUASHIDA Heat shrinkable sleeve Widely used in thermal insulation pipe joint sealing anticorrosion waterproof end cap, municipal drainage and sewage pipe connection mending, inspection wells, steel belt reinforced spiral corrugated pipe, especially for the size of the head, anticorrosive sealing, to solve the drag pipe, corrugated pipe heat-shrinkable tape mending products contraction not to the end of the problem!
Thickness of 1.8/2.0/2.5/3.0mm according to different environments to choose different products.
Width 80-800mm can be customized.
| ITEM | Standard | UNIT | Data | |
| Adhesive | softening point | ASTM E 28 | °C | 70-80 |
| shear strength | DIN 30 672 | N/cm | ≥100 | |
| Basic | specific density | ASTM D792 | r/cm 3 | 0.935-0.96 |
| tensile strength | ASTM D638 | Mpa | 15-20 | |
| Elongation at break | ASTM D792 | % | 350 | |
| hardness | ASTM D2240 | ball | 48 | |
| Heat Shrinkable Sleeve | peel strength | ASTM D1000 | N/cm | >150 |
| water-intake rate | ASTM D570 | % | 0.05 |
Move the heat shrink sleeve to the centered position at the joint and take out the isolation material. Heat evenly from the center along the circumference, make it shrink completely and then extend the heating to both ends respectively. Pay attention to the even fire. After all the shrinkage is completed, reheat the uneven surface to make it completely flat. After the overall heating is completed, turn down the flame and reheat again to make the hot melt adhesive fully overflow. During the heating process, use the pressure roller to roll the joint several times, focusing on rolling the fusion lap to eliminate air bubbles.
Feature
1.Fast shrinkage speed,
2.good waterproof performance,
3 good anti-corrosive performance,
4.long service life, convenient transportation and fast construction.
2. 3Layer Fiber
reinforced PE heat shrinkable tape (sleeve) is composed of cross-linked polyethylene back, a middle layer of fiber and special heat melt adhesive an. The 3 layer reinforced sleeve gives better shrink ratio, and better strength. It is resistant to corrosion, wear, impact, UV and aging, easier to be operated.
Application area:
It is mainly used for Hollow wall spiral pipe, corrugated pipe and metal reinforced corrugated spiral pipe etc.
TEST PROCEDURE
1. Clean the steel pipe and heat it by fire till over 80 ºC
2. Paint the steel pipe with Primer (mixed with A&B)
3. Fire heat the heat shrink sleeve, be attention to start heating from middle of the sleeve, but act from up and down, and gradually move from middle to two sides of sleeve, in order to drive air out of the sleeve, after finish heating, the good result is that there is about 1-2mm hot adhesive melt at the edge of sleeve.
TEST RESULT
1. Test result after cooling about 40 minutes.
Peel strength to primer is over 100N per 2cm(till the end of the spring balance). at 30.7ºC
Co-adhesive: Half-half.
2. Test result after cooling about 24hours.
Peel strength to primer is over 172N per 2cm at room temperature about 30.7ºC
Co-adhesive: Half-half.
3. 2. Test result after cooling about 24hours.
Peel strength to primer is over 9.2kg/90N per 1cm at room temperature about 30.7ºC
Co-adhesive: Half-half.
Company Details
Business Type:
Manufacturer
Year Established:
2003
Total Annual:
3000000-5000000
Employee Number:
100~200
Ecer Certification：
Verified Supplier
1. Our Factory Qingdao Huashida Machinery Co., Ltd. is located in Qingdao High & New Technology Industrial Area- Qingdao Huashida industrial Park, covers an area of about 4000 square meters. We have tens of years experience in plastic pipe, sheet, and board extrusion lines, and pipe... 1. Our Factory Qingdao Huashida Machinery Co., Ltd. is located in Qingdao High & New Technology Industrial Area- Qingdao Huashida industrial Park, covers an area of about 4000 square meters. We have tens of years experience in plastic pipe, sheet, and board extrusion lines, and pipe...
Get in touch with us
Leave a Message, we will call you back quickly!