ISO 13kg/Cm2 58cm Ndfeb Magnetic Lathe Chuck

Product Specification

X71 circular electro permanent magnetic chuck

Product Introduction

1. Strong magnetic force, high precision machining

Table maximum suction 13-16kg / cm ², is about 2 times the ordinary magnetic sucker to ensure that the workpiece fixture will not be a clear shift, due to the processing process does not require power supply, so this product does not exist thermal deformation, effectively guarantee The processing accuracy.

2. Strong security, energy saving and environmental protection

Machining center sucker in the course of the work does not require electricity, rely on permanent magnet suction suction workpieces, to avoid the electromagnetic system in the sudden power failure and damage to the magnetic loss of the workpiece and the risk of falling off the workpiece. As the permanent magnet sucker only in the magnetization and demagnetization process within 1-2 seconds of the use of electricity, work without the use of any energy and produce safe, strong and efficient force, both economic and environmentally friendly.

This new type of CNC machining center disk in the instant power after the permanent magnet can be hardened workpiece positioning processing, the application of reverse current, you can demolish the workpiece removed, safe and energy saving, easy to operate, no temperature rise and change, processing accuracy high.

Strong support. In theory, the unit of permanent magnet fixture clamping force of 150KN, far greater than the cutting force, even the uneven surface of the fur, but also safe to suck, even if the milling quality of 52HRC hardened hardened workpiece, the same can normal work.

3.Save cost,no remanence cost.

Magnetic flux leakage phenomenon. Electromagnetic permanent magnet fixture in the suction clamping process, but there is magnetic force on the surface of the fixture, the other surface does not exist magnetic flux leakage phenomenon, not only the tool without any effect, and remove the workpiece, the fixture and the workpiece will not exist remanence , Because the system has an internal electro mechanical demagnetization device, the workpiece and fixture can be automatically demagnetized.

4. easy to use.

The advantage of the permanent magnet fixture is that the workpiece positioning and clamping is very convenient, do not need cumbersome and strenuous manpower operation. At the same time, because the suction force is only in the bottom of the workpiece, the workpiece does not need to use the clamping plate clamping, to avoid the clamping force caused by the workpiece deformation and scratches. The permanent magnet fixture can realize the automatic adjustment of the workpiece. At the same time, it can realize the machine tool without vibration cutting, grinding, milling and so on, which can prolong the service life of the machine.

Product Parameters

More processing schemes can be provided by using different magnetic

guide blocks pardigm as below

PULSE CONTROLLER

Product introduction:

safety protection: The spindle linkage can be realized by unlocking the input contact signal and themagnetized output contact. lt is equipped with adjustable magnetoelectric current (or short circuit)protection and undercurrent (or circuit break) alarm functions.

Simple operation: all setting parameters and running state can be monitored through the host panel, andthe power frequency can be automatically tracked;Flexible configuration, easy to use.

control interface: it is equipped with a variety of alternative control interfaces, which can satisfy allkinds of on-line control requirements. It also has alternative control (remote) or PLC interfaces.

Install and Use

INSTRALL

Fixed In Clamp Slot

Secure With Screw Holes

MAGNETIZATION STEPS

1. Plug in

2. Press the

magnetization button

3. Until the green light isalways on

4. Unplug the plug andciose the cover

DEMAGNETIZATION STEPS

1. Plug in

2. Press the demagnetization button

3. Until the red light isalways on

4. Unplug the plug andclose the cover

1. Cnc Flame Cutting

2. Gantry Milling

3. Cnc Processing Centor

6. Coils and Magnetic Steel Assembly

5. Deburring and Cleaning

4. Drilling Machine

7. Magnetic Steel Commissioning

8. Electrical with Stand Voltage Detection

9. Epoxy Potting

10. Suction and Pull-out Force Test

11. Surface Grinder Finish Machining

12. Surface Magnetic Remanence (inspection)

13. Finished Product Electrical with Stand Voltage Detection

14. Finished Product Appearance Inspection

15. Packing List Inspection

16. Finished Package

Company Profile

As a professional designer and manufacturer ofmagnetic products over 10 years, Wuxi Jiuyicheng Technology Company Limited is always providing customers appro-priate solutions to holding and lifting materialduring machining progressing.

The huge range of our magnetic products includeElectro magnetic chuck(EMC) series, Permanentmagnetic chuck(PMC) series, Electro permanentmagnetic chuck(EPMC) series, Electro magneticlifter (EML),.Permanent magnetic lifter(PM-L),Electro permanent magnetic lifter (EPML),Iron remover, Demagnetizer, etc.

Magnet is widely used in industries like metallurgy, machinery, shipbuilding, electric power, mine, automobile manufacturing, rail transportation and so on.

There is mainly 3 kinds of magnet, permanent magnet, electromagnet, permanent electromagnet. different magnet is suitable for different areas, and as a professional supplier of magnetic tools, JYC technology is is always providing customers appropriate solutions for our customers.

FAQ

Q: Are you manufactory or trade company.