Glass And Aluminium Marking UV Flying Laser Marker Supported AI DXF

Product Specification

Industry Laser Marking Machine For Production Line UV CO2 Marking Machine

PRODUCT PARAMETER

PRODUCT DESCREPTION

UV Laser Marking Machine Introduction

Ultraviolet laser device, which has the properties of a laser device, can perform online orientation functions on convection lines, aimed mainly at surface marking of thin fragile objects, such as photoelectric solar glass, etc.

Ultraviolet laser strike machines belong to the mark laser strike ser one of the product, the mark and the latest laser development processing technologist, behind the tradition of laser fixture laser foot processor laser has been rejiagong technologist, at a tonk of half an hour elevated Spaces has a limited-development, however ultraviolet laser mark hammer pointing yawn lengjiagong, at a tonk of a degree, the lowest level of thermal impact - a huge leap in laser technology.

Matters Needing Attention

1. Before use, pay attention to check whether each connection part is loose or damaged
2. UV UV laser marking machine regularly replace the filter.
3. All transmission and swing parts need to be lubricated, and the right amount of lubricant should be maintained for the transmission chain and other parts.
4. After the UV laser marking machine is used, the equipment should be maintained in time and the equipment should be regularly checked.

HOW TO USE LASER MARKING MACHINE

A boot steps:

① Check that the ground cable of the device is grounded.
② Check whether the power cord of the laser marking machine is correctly connected and reliable.
③ Insert the key switch, turn 90o clockwise to the "on" position, turn on the main power supply, and the power indicator is on.
④ Confirm that the laser marking machine emergency stop switch is pressed.
⑤ Turn on the power switch of the computer host and computer monitor.
⑥ Rotate the red emergency stop switch in the direction of the arrow, so that it springs up, you can turn on the laser head power supply, about 1 minute after the laser head is started.
⑦ Remove the lens cap; At this point, the laser marking machine is opened and can accept the operator's command for marking operation.

Two dozen mark operation
① Double-click the marking program icon to enter the program.
② Select the marking file, double-click the date and time in the content to modify, click OK, the modification is complete.

Three dozen mark test and print position
① On the workbench or production line, place a test piece equal to the height of the marking workpiece, and confirm that the test piece is indeed stable.
② Mark by operating the marking control software. To make the marking effect the most. Preferably, the following steps can be adjusted.

Fourth, adjust the focal length by adjusting the head lifting device.
① Adjust power, marking speed and other parameters in the marking software.
② Enter the software, double-click the print date, and drag it up and down with the mouse to adjust the print position to the appropriate position.
③ Print test can be carried out after completing the above steps.
④ After the test is correct, re-mark the workpiece.

Five-off
① Press the red mushroom button (emergency stop switch) to cut off the laser head power supply.
② After confirming that the industrial computer does not run any software, exit and shut down normally.
③ Turn the key switch 90o counterclockwise to the "off" position, turn off the main power supply of the marking machin

PACKAGE AND SHIPMENT

1.We have three layers package. For the outside, we adopt wood craft case. In the middle, the machine is covered by foam, to protect the machine from shaking. For the inside layer, the machine is covered by thickening plastic bag for waterproof.

2.Air-worthy packing or Sea packing which with international standard.

SERVICE

1.one year quality guaranty, the machine with main parts shall be changed free of charge when if any problem during the warranty period.

2. Lifetime maintenance free of charge.

3. Free training course at our plant.

4. 24 hours on line service each day, free technical support.

5.Machine has been adjusted before delivery.

6.For free sample testing, please send us your file, we will do marking here and make video to show you the effect, or send sample to you for checking quality.

FAQ

Q1. What support do I get with my laser machine?