China High Quality Best Price ASME B16.9 ASTM A234 WPB 90 Degress LR SMLS Elbow

Product Specification

ASME B16.9 ASTM A234 WPB 90 Degress LR SMLS Elbow

1.

ASME B16.9 ASTM A234 WPB 90 Degress LR SMLS Elbow

1. What is the A234 WPB ?

   ASTM A234 WPB Elbow is the standard specification for pipe fittings Elbow of wrought carbon steel and alloy steel for moderate and high-temperature service. SA234 WPB Elbow in accordance with ASME B16.9.Carbon steel pipe fittings manufactured to ASMT A234 are usually furnished in the butt-welding form in accordance with ASME B16.9 or ASME B16.49. CS Elbow A234 WPB are widely used in different industries like power, engineering, construction and many mor

2. 

   ASTM A234 Wpb Elbow Dimensions

    

   Nominal Pipe Size	Outside Diameter	Inside Diameter	Wall Thickness	Center To End	Pipe Schedule	Weight Pounds
   1/2	0.84	0.622	0.109	0.62	40	0.09
   3/4	1.05	0.824	0.113	0.75	40	0.1
   1	1.32	1.05	0.133	0.88	40	0.22
   1 1/4	1.66	1.38	0.14	1	40	0.33
   1 1/2	1.9	1.61	0.145	1.12	40	0.43
   2	2.38	2.07	0.154	1.38	40	0.85
   2 1/2	2.88	2.47	0.203	1.75	40	1.7
   3	3.5	3.07	0.216	2	40	2.5
   3 1/2	4	3.55	0.226	2.25	40	3.4
   4	4.5	4.03	0.237	2.5	40	4.5
   5	5.56	5.05	0.258	3.12	40	7.5
   6	6.62	6.06	0.28	3.75	40	11.7
   8	8.62	7.98	0.322	5	40	23.3
   10	10.75	10.02	0.365	6.25	40	40.9
   12	12.75	12	0.375	7.5	*	61.4
   14	14	13.25	0.375	8.75	30	78.1
   16	16	15.25	0.375	10	30	101
   18	18	17.25	0.375	11.25	*	128
   20	20	19.25	0.375	12.5	20	159
   24	24	23.25	0.375	15	20	231
   30	30	29.25	0.375	18.5	*	358
   36	36	35.25	0.375	22.25	*	518
   42	42	41.25	0.375	26	*	707
   48	48	47.25	0.375	29.88	*	1,000

   3.SA234 WPB Elbow Equivalent

   Pipe	Pipe Elbow Fitting	Flanges	Valves	Bolts & Nuts
   A106 Gr A	A234 Gr WPA elbow	A105	A216 Gr WCB	A193 Gr B7 A194 Gr 2H
   A106 Gr B	ASTM A234 gr WPB elbow	A105	A216 Gr WCB
   A106 Gr C	A234 Gr WPC elbow	A105	A216 Gr WCB

   ASTM A234 gr WPB elbow Chemical Composition

   Chemical Composition (%) of ASTM A234 Pipe Elbow

   WPB B,C,D,E,	WPC C,D,E,	WP11 CL1	WP11 CL2,	WP11 CL3	WP22 CL1,	WP22 CL3	WP5 CL1,	WP5 CL3	WP9 CL1,	WP9 CL3	WP91
   Carbon	0.3	0.35	0.05–0.15	0.05–0.20	0.05–0.20	0.05–0.15	0.05–0.15	0.15	0.15	0.15	0.08–0.12
   Manganese	0.29–1.06	0.29–1.06	0.30–0.60	0.30–0.80	0.30–0.80	0.30–0.60	0.30–0.60	0.30–0.60	0.30–0.60	0.30–0.60	0.30–0.60
   Phosporus	0.05	0.05	0.03	0.04	0.04	0.04	0.04	0.04	0.03	0.03	0.02
   Sulfur	0.058	0.058	0.03	0.04	0.04	0.04	0.04	0.03	0.03	0.03	0.01
   Silicon	0.10 min	0.10 min	0.50–1.00	0.50–1.00	0.50–1.00	0.5	0.5	0.5	1	1	0.20–0.50
   Chromium	0.4	0.4	1.00–1.50	1.00–1.50	1.00–1.50	1.90–2.60	1.90–2.60	4.0–6.0	8.0–10.0	8.0–10.0	8.0–9.5
   Molybdenum	0.15 max	0.15 max	0.44–0.65	0.44–0.65	0.44–0.65	0.87–1.13	0.87–1.13	0.44–0.65	0.90–1.10	0.90–1.10	0.85–1.05
   Nickel	0.4	0.4	…	…	…	…	…	…	…	…	0.4
   Copper	0.4	0.4	…	…	…	…	…	…	…	…	…
   Others	Vanadium 0.08	Vanadium 0.08	…	…	…	…	…	…	…	…	Vanadium 0.18–0.25 Columbium 0.06-0.10 Nitrogen 0.03-0.07 Aluminum 0.02F Titanium 0.01F Zirconium 0.01F

   Notes:

   For each reduction of 0.01% below the specified C maximum, an increase of 0.06% Mn above the specified maximum will be permitted, up to a maximum of 1.35%.

   The sum of Cr and Mo shall not exceed 0.32%.

   The sum of Cu, Ni, Cr, and Mo shall not exceed 1.00%.

   The maximum carbon equivalent (C.E.) shall be 0.50, based on heat analysis and the formula C.E.=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15.

   4.SA234 WPB Elbow Mechanical Properties

   Check below ASTM A234 WPB Elbow Mechanical Properties before you order.

   Tensile Requirements	WPB	WPC, WP11CL2	WP11CL1	WP11CL3
   Tensile Strength, min, ksi[MPa]	60-85	70-95	60-85	75-100
   (0.2% offset or 0.5% extension-under-load)	[415-585]	[485-655]	[415-585]	[520-690]
   Yield Strength, min, ksi[MPa]	32	40	30	45
   	[240]	[275]	[205]	[310]

   SA234 WPB Elbow Elongation Properties

   	WPB, WPC, WP11, WP22		WP91
   	Longitundinal	Transverse	Longitundinal	Transverse
   Standard round specimen, or small proportioanl specimen, min % in 4 D	22	14	20	13
   Rectangular speicmen for wall thickness 5/16″ and over, and for all small sizes tested in full section; min % in 2 in.	30	20 A
   Rectangular speicimen for wall thickness less than 5/16″; min % in 2 in (1/2″ wide specimen)	B	B

   Where the wall thickness lies between two values above, the min elongation value is determined by the following equations:

   Longitudinal E=48t+15.00

   Transverse E=32t+10.00

   E = elongation in 2in [50mm], %

   t = actual thickness of specimen, in [mm]

   5.Available SA234 WPB Elbow size chart

    

   ASTM A234 WPB Elbows, 180 Degrees Bending Angle	ASTM A234 GR WP5 180 Degree Seamless Elbow SR BW SCH.40
   Seamless Elbow LR, ASTM A234 WP9, BW, 90 Degree, 6 Inch	ASTM A234 WP5 90° Seamless Elbow LR, 8 Inch, Sch. XS
   45D & 90D Elbow, A234 WPB, 3 Inch, Butt Weld Ends	Welded 90D Elbows, 26 Inch, LR, ASTM A234 WPB
   BW 90 Deg Elbows, ASTM A234 WPB, DN1200, WT Sch XS, LR, ASME B16.9	3LPE Coated Elbows, ASTM A234 WPB, 10 Inch, SCH 40, B16.9, FEB Lined
   90 Degree FBE Lined Elbows, ASTM A234 WPB, 8 Inch, SCH 40, B16.9	45 Degree LR Elbow, ASTM A234 WPB, 22 Inch, 0.375 Inch, BW
   ASTM A234 WPB 90 Degree LR Elbows, SCH 60, 16 Inch, Butt Weld	A234 WPB 90 Degree Elbows, Long Radius, 6 Inch, SCH 40, Black
   Long Radius Elbows, 90 Degree, A234 WPB, 10 Inch, SCH 40, Seamless	A234 WPB Seamless Long Radius Elbows, 90 Degree, 2 Inch, SCH 40
   A234 WPB 90D LR Elbows, ASME B16.9, 12 Inch, SCH 80, OD 300mm	A234 WPB SMLS Elbows, 4 Inch, SCH 40, Long Radius, BE Ends
   A234 WPB 90 Deg Elbows, 10 Inch, SCH 40, LR Elbow	90D LR Elbows, A234 WPB, B16.9, DN200, SCH 40, BW Ends
   ASME B16.9 SMLS Elbows, 90D, ASTM A234 WPB, 6 Inch, SCH-STD	ANSI B16.9 Elbows 90°ASTM A234 WPB 16 Inch Butt Weld

   6.PICTURES SHOWING