90L FM200 Cylinder Working Pressure 5.6Mpa Red FM200 Containers

Product Specification

Red Fm200 Containers 90L Fm200 Cylinder Working Pressure 5.6Mpa

Application scope, precautions and reasons why the heptafluoropropane system cannot extinguish fire

1. Scope of application

Applicable to the following places: museums, libraries, data rooms, archives warehouses, etc.

2. Precautions for daily use

(i) Trained personnel shall conduct daily appearance and pressure display value inspections of the entire system to check whether there are any abnormalities in the system.

(ii) All components shall be inspected monthly. All components shall be free of collision deformation and other mechanical damage, the surface shall be free of rust, the protective coating shall be intact, the nameplate shall be clear, and the lead seal and safety mark of the manual operating device shall be complete.

(iii) The fire extinguishing agent storage container shall be weighed and inspected once a year. If the weight drops by more than 5%, the storage cylinder must be refilled or replaced.

(iv) The HFC-227ea cylinder shall be inspected every three years, and the fire extinguishing agent storage container and container valve shall be tested for strength and sealing performance every five years.

(v) The heptafluoropropane cylinders shall be tested every three years, and the fire extinguishing agent storage containers and container valves shall be tested for strength and sealing performance every five years. Only after passing the test can they continue to be used.

3. Reasons why the HFC-227ea fire extinguishing device does not spray

(i) The fire alarm host is in manual mode

The HFC-227ea fire extinguishing system has three ways to start: automatic start, electrical manual start, and mechanical emergency manual start. In the electrical manual start mode, the fire detection system can only detect and alarm the protection area, and cannot start the fire extinguishing device by itself. It is necessary to manually press the start button on the fire alarm controller panel or the emergency start-stop button outside the protection area door. The fire alarm controller receives the start command and starts the fire extinguishing device according to the predetermined procedure.

(ii) The solenoid valve is not installed correctly or the safety pin

The electromagnetic drive device is installed on the container valve. When extinguishing the fire, the electromagnet breaks through the working diaphragm on the container valve when it is actuated, so that the fire extinguishing agent is released. If it is not installed correctly, the fire extinguishing agent cannot be released, resulting in fire extinguishing failure.

(iii) Insufficient starting power

When a fire occurs, the fire extinguishing device allocates insufficient power, resulting in the inability to drive the solenoid valve, the electromagnet cannot act, and the working diaphragm on the container valve cannot be broken. As a result, HFC-227ea cannot be started, or partially cannot be started. The HFC-227ea fire extinguishing system does not comply with the regulations.

(IV) Heptafluoropropane agent leaked, and the amount of agent did not reach the amount required for fire extinguishing, resulting in fire extinguishing failure.

(V) Other reasons

For example, the selector valve was out of repair for a long time, resulting in insensitive action and inability to effectively spray heptafluoropropane fire extinguishing agent. Or the equipment pressure was abnormal, resulting in the inability to release the fire extinguishing agent normally.

Company introduction:

Guangzhou Rongan Fire Protection Equipment Co., Ltd. is a professional manufacturer of fire protection facilities integrating R&D, production, design and sales services. The company has experts from the national fire protection industry standards committee and a group of professional technical service teams with more than ten years of experience in the fire protection industry, and will spare no effort to provide you with the most intimate and professional comprehensive technical solutions for fire protection engineering products. "Rongxiao" series products produced by the company have passed the national compulsory product certification and the national fixed fire extinguishing system inspection center, with reliable quality and stable performance, and the factory has passed the ISO9001 quality system certification.

Frequently asked questions:

Q1: Are you a manufacturer or a trading company? A1: We are manufacturers.

Q2: How long is the delivery time? A2:10 days, which can be negotiated according to the quantity.

Q3: How to deal with the fault? A3: During the warranty period, we will provide you with a remote emergency plan during working hours. During the free maintenance period, the company will replace spare parts or complete machines that have failed due to defects or quality problems free of charge.