Slim Aluminium Window Profiles Bending For Sash Windows Peru Wood Finish

Product Specification

Peru Wood Finish Aluminum Profile For Sash Windows Aluminium Window Profiles
 
Basic Information

 
Product Display
 

 
Door and window technology
1. The sealing problem of aluminum alloy doors and windows: the biggest problem of the push-pull system is the poor sealing
In Beijing, the mainstream of doors and windows is still sliding windows. However, due to the simplicity and objective limitations of doors, most of them are sliding doors. However, there are some problems with simple sliding doors. If you imagine the heat convection inside and outside a door, how big is this impact? ?
In many projects, it will be found that due to insufficient thermal insulation materials for casement windows, some good thermal insulation strips also have the phenomenon of throttling, but sliding windows do not. Therefore, the use of simple sliding doors is actually beneficial to the entire building energy-saving system. Said, forming one of the biggest weak links. Talking about the lock system of doors and windows, we often see the single-point lock system. Generally speaking, it must have a certain degree of wind resistance. In the sliding door system, the lock wall of the entire door is only a limit system, which does not allow the door to be locked. Free movement, simple push-pull systems are all mobile, and they cannot move when they touch the window frame. The entire sunken window frame does not form a pressure structure. In a sense, this lock point is very fragile against anti-theft Said to have the effect of anti-theft, for the whole effect, the applicability has not improved.
In Europe, there are many uses for sliding doors, and the most common is the inward sliding door system. Passing the Buick commercial vehicle is the inward sliding door system. For the application of a simple sliding door, it may be calculated that the thermal insulation can be achieved due to the use of the thermal insulation substrate, but it is disadvantageous for the essence of use.
China's door and window testing standards require that all opening seams completely ignore the influence of air tightness, and do not test the air tightness of the entire frame system or the complete door and window system. This is essentially different from the European standard. The European testing system is to send the complete window directly from the hole to the laboratory for testing. If the window leaks, the heat insulation reaches 40%, and the test cannot pass. When using China to pass the inspection doors and windows, it will still feel cold in winter.
2. The design of aluminum alloy doors and windows is regrettable: there is one more layer in the thermal insulation aluminum alloy door and window system.
In China, there are two arguments for placing this layer in the room, one is anti-theft, and the other is easy to disassemble. The second reason is that it exists, especially in high-rise buildings. As for the anti-theft function, it is completely unnecessary.
For an outward opening window, the insulating glass is on the outside, and the thermal insulation profile system must use two-way structural profiles, and one-way can also be used. It is not possible to open it large, and if a large amount of insulating glass is pressed on the outside, it is difficult to divide the force into two points. The thermal insulation aluminum alloy door and window system is a composite structure, and any link cannot be weak. As long as one link is weak, the entire frame system can play a role.
As a feature of the thermal insulation aluminum alloy door and window system, due to the lack of design, the structure has undergone qualitative changes, which cannot be understood in the traditional home improvement process. This is a very critical point.
3. The acceptance defect of aluminum alloy doors and windows: the result of brutal operation is to move the handle up to a position of 30 degrees
During the transportation of doors and windows, when the doors and windows of the project are installed, when the doors and windows of a car are unloaded, they will find that there are basically no first-level constructors on them. There are bumps in the process of transportation. It is a fatal injury, so there will be no such thing in the door and window factory.
When it comes to hardcover, we generally say that hardcover is a high-end room, but the characteristics of interior decoration workers: they do not understand doors and windows, and often hardcover projects choose high-end door and window systems, but they do not understand for general decoration, and wait until the end of hardcover. At times, the small owner will find that the hardware of the doors and windows should be closed and opened like this, but finally found that the handle is moved up 30 degrees, and when it is opened, it goes up with a hand. This is the improper use of the interior workers and brutal operation. the result of. Most small owners see their doors and windows in this situation when they move in, I believe it is difficult to accept.
Hardware is the two major functions, one is to lock the wall, and the other is to bear the load. A systematic process, as a door and window, from the factory to the construction site, design to transportation, installation, acceptance, including the replacement of problems, including the owner's personalized needs for doors and windows. Throughout the process, there needs to be perfect expression.
Fourth, the bump problem of aluminum alloy doors and windows: must be solved in time
When the aluminum alloy door and window sash is less than 650, the outside and the main rubber strip will collide, which is fatal. What is the sound of the bump? When I hear a click when it is opened, how will the workers solve it? I quickly hit it with my hands a few times. Is there any sound? Why not? Maybe the rubber strip has been knocked off. , the main seal of aluminum alloy doors and windows can not be achieved.
The wind pressure resistance performance of doors and windows has always been relatively simple. Professional door and window factories must provide corresponding calculation books. I went to Shandong to see a project two days ago. To strengthen the center, it must be a piece with protrusions on the rigid profile, but The protruding part should be connected with the wall accordingly, and the two ends must be fixed. When the reinforcement is deep enough to be below the plane, there will be a problem. One end leaks there, one end is fixed, and the other end is shaking. This reinforcement is absolutely necessary. Some profiles are bought with money, and if used improperly, they will lose their meaning.
  
Certificates and Honors
 

 
Factory display
 
 
 
 
 
Company Profile
 
Jiangyin Longkang Metal Products Co., Ltd. is located in Zhouzhuang Town, Jiangyin City - the largest aluminum extrusion profile production base. Covering an area of more than 35,000 square meters with more than 350 employees. We focus on metal customization, special-shaped aluminum profiles, aluminum profiles, aluminum tubes, rail transit series, doors and windows aluminum profiles, heat sinks, CNC processed aluminum profiles, interior decoration series, bending series, etc. We also have precision anodizing and various surface treatments, such as PVC film, wood grain, electrophoresis, powder coating, anodizing, etc. After more than 20 years of development, The company has become a modern aluminum production enterprise with perfect quality management system.
 
The company has the ability to develop and design molds independently, we can produce any extruded aluminum profiles according to your mechanical drawing or sample. Longkang has 10 extrusion production lines (600-3500 tons), one automatic oxidation electrophoresis production line, vertical and horizontal spraying production line per each, and a variety of advanced supporting production, processing and testing equipments. There are also CNT digital control drilling and milling machine(CNC), double head saw, hydraulic saw and punching machine in our processing workshop. The complete technological process can benefit to reduce the production turnover times for semi-finished products, to avoid the damage during transportation, improve the production efficiency, reduce the cost of production,and to ensure the quality and delivery time.
 
Efficiently treating our customers as partners with sincerity, specialization and satisfaction is our managerial principle. Attributed to the backup of a dedicated technical team, filled with wide and profound knowledge and practice in aluminum profile and world trade for 20 years, the company owns rich experience in product quality control and profile physical properties such as Hardness, Stretchability, Flatness, Straightness, and Tolerance etc. In line with the principle of sharing the preferential cost and joint development, the company has formed an interest community for years with its customers at home and abroad. Sincerely to build up a pleasant mutual trust, cooperative, win-win and value-added sustainable partnership is what we are achieving to grow together with you!
 
FAQ
 
Q: Can you send me the product catalog and price?
A: Leave your e-mail or other contact information, the product catalog will be provided here
The real-time price needs to confirm the specific product specifications and quantity, so the price can be calculated for you only when you provide drawings or plans, etc.
 
Q: Do you provide samples?
A: Yes (special customized samples need to provide drawings).
 
Q: What is the thickness of the anodizing? Can you do 12um?
A: Our normal thickness is about 10 um. Yes, we can do 15 microns and above.