Product Specification

  UNO R3 /1602 LCD Servo Motor Dot Matrix Breadboard LED starter kit for Arduino
 
  
Feature:
For UNO R3  board component basic element pack starter kit, bread board, light dependent resistors, flame sensor etc. Great for DIY starters and beginners,This is a very good kits for starter to study MCU programing .
With This  Uno R3 Starter Kit , you are able to learn and do many experiment such as 
lighting up the LED , then get the LED to be a output display,And interact with you .also you can learn the basic concepts of buttons , IR remote control with IR receiver . Use sensors (flame , temperature sensor) to detect the environment , also this includes Servo , Motor , ULN2003 driver board to let you complete Mechanical control over objects . with LCD modules to display your work.with this kit , you will enjoy a lot of fun and also learn from it

This kit walks you through the basics of using the   in a hands on way. You'll learn through building several creative 

projects. The kit includes a selection of the most common ones. Starting the basics of electronics, to more complex 

projects, the kit will help you control the physical world with sensor and actuators.

 
Packing List:
 

UNO R3 Board 1
Mini Breadboard shield with mini board 1
830 points Breadboard 1
SMD components bo 1
LED red yellow green 15(each 5pcs)
Buzzer 2
Switch 4
Digital tube 2
Mercury switch or ball switch 2
Photoresistor 3
Potentiometer 1
Flame sensor 1
Infrared receiver 1
Resistance 220R, 1K, 10K 15(each 5pcs)
LM35 Temperature sensor 1
USB Cable 1
Male to male jumper wire 30
9V battery clip 1
IR mini remote control 1
1602 LCD LCD module 1
9G Servo 1
5V stepper motor + ULN2003 driver board 1
74HC595  1
8*8 DOT MATRIX   1
 
About boards for UNO R3 Instrctino:
 
The Uno is a microcontroller board based on the ATmega328 . It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
The Uno differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features the Atmega16U2 (Atmega8U2 up to version R2) programmed as a USB-to-serial converter.
Revision 2 of the Uno board has a resistor pulling the 8U2 HWB line to ground, making it easier to put into DFU mode.
Revision 3 of the board has the following new features:
 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible with both the board that uses the AVR, which operates with 5V and with the Due that operates with 3.3V. The second one is a not connected pin, that is reserved for future purposes.
Stronger RESET circuit.
Atmega 16U2 replace the 8U2.
"Uno" means one in Italian and is named to mark the upcoming release  The Uno and version 1.0 will be the reference versions  , moving forward. The Uno is the latest in a series of USB   boards, and the reference model for the DIY  platform.
 
Summary of 2012 UNO R3 Board
Microcontroller ATmega328
Operating Voltage 5V
Input Voltage (recommended) 7-12V
Input Voltage (limits) 6-20V
Digital I/O Pins 14 (of which 6 provide PWM output)
Analog Input Pins 6
DC Current per I/O Pin 40 mA
DC Current for 3.3V Pin 50 mA
Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader
SRAM 2 KB (ATmega328)
EEPROM 1 KB (ATmega328)
Clock Speed 16 MHz

Our Team:

Awards:

Competitive Advantages:

1.Convenient & Friendly Customer Service.

2.Low Prices Direct From Factory Suppliers.

3.Fast Delivery Around the World.

4.High Quality With Global Standards.

5.One Year Factory Warranty.

6.Safe Shipping Way and Payment.