EMC Programmable IC Chips Compliant Slew Rate Limited EI , Timer IC Chip

Product Specification

EMC Programmable IC Chips Compliant Slew Rate Limited EI , Timer IC Chip

ADM483EAEZ  EMC Compliant Slew Rate Limited EIA RS-485 Transceiver

FEATURES

 Robust RS-485 Transceiver

15 kV ESD Protection Using HBM

2 kV EFT Protection Meets IEC1000-4-4 High

EM Immunity Meets IEC1000-4-3

Reduced Slew Rate for Low EM Interference 250 kbps Data Rate

Single +5 V 6 10% Supply

–7 V to +12 V Bus Common-Mode Range 12 kV Input Impedance

Short Circuit Protection Excellent Noise Immunity 36 mA Supply Current 0.1 mA Shutdown Current

APPLICATIONS

Low Power RS-485 Systems Electrically Harsh Environments EMI Sensitive Applications DTE-DCE Interface Packet Switching Local Area Networks

GENERAL DESCRIPTION

The ADM483E is a robust, low power differential line transceiver suitable for communication on multipoint bus transmission lines. Internal protection against electrostatic discharge (ESD), electrical fast transient (EFT) and electromagnetic immunity (EMI) allows operation in electrically harsh environments. ESD protection on the I-O lines meets ± 15 kV when tested using the Human Body Model. EFT protection meets ±2 kV in accordance with IEC1000-4-4, while EMI immunity is in excess of 10 V/m meeting IEC1000-4-3. The level of unwanted emissions is also carefully controlled using slew limiting on the driver outputs. This reduces reflections with improperly terminated cables and also minimizes electromagnetic interference. The controlled slew rate limits the data rate to 250 kbps. The ADM483E is intended for balanced data transmission and complies with both EIA Standards RS-485 and RS-422. It contains a differential line driver and a differential line receiver and is suitable for half duplex data transmission, as the driver and receiver share the same differential pins. The input impedance on the ADM483E is 12 kΩ, allowing up to 32 transceivers on the bus. The ADM483E operates from a single +5 V ± 10% power supply. Excessive power dissipation caused by bus contention or by output shorting is prevented by a thermal shutdown circuit. This feature forces the driver output into a high impedance state if, during fault conditions, a significant temperature increase is detected in the internal driver circuitry. The receiver contains a fail-safe feature that results in a logic high output state if the inputs are unconnected (floating). The ADM483E is fabricated on BiCMOS, an advanced mixed technology process combining low power CMOS with robust bipolar technology. It is fully specified over the industrial temperature range and is available in 8-lead DIP and SOIC packages.

ABSOLUTE MAXIMUM RATINGS* (TA = +25°C unless otherwise noted)

VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+7 V

Inputs Driver Input (DI) . . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V

Control Inputs (DE, RE) . . . . . . . . . . –0.5 V to VCC + 0.5 V

Receiver Inputs (A, B) . . . . . . . . . . . . . . . . . –14 V to +14 V

Outputs Driver Outputs . . . . . . . . . . . . . . . . . . . . –12.5 V to +12.5 V

Receiver Output . . . . . . . . . . . . . . . . . –0.5 V to VCC +0.5 V

ESD Rating: Air (Human Body Model) (A, B Pins) . . ±15 kV

ESD Rating: Contact (Human Body Model) (A, B Pins) . . . . . . . . . . . .  . . . . . . . . . . ±8 kV

ESD Rating MIL-STD-883B Method 3015 (Except A, B) . . . . . . . . . . . . . . . . . . ±3.5 kV

EFT Rating (IEC1000-4-4) (A, B Pins) . . . . . . . . . . . . ±2 kV

EMI Immunity (IEC1000-4-3) . . . . . . . . . . . . . . . . . . 10 V/m

Power Dissipation 8-Pin DIP . . . . . . . . . . . . . . . . . . . 727 mW θJA,

Thermal Impedance . . . . . . . . . . . . . . . . . . +135°C/W

Power Dissipation 8-Pin SOIC . . . . . . . . . . . . . . . . . 470 mW θJA,

Thermal Impedance . . . . . . . . . . . . . . . . . . +110°C/W

Operating Temperature Range Industrial (A Version) . . . . . . . . . . . . . . . . –40°C to +85°C

Storage Temperature Range . . . . . . . . . . . –65°C to +150°C

Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . . +300°C

Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . +215°C

Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . +220°C