LCD Touch Screen Mini Electric Cool Box , Mini Portable Cooler For Car

Product Specification

mini car refrigerator car cool box with LCD touch screen digital display thermostat 18L

Precautions

1. After the refrigerator is unpacked, please leave it upright for more than 6 hours before you connect it with electricity.

2. The refrigerator should be placed horizontally during work. If there is an angle for a long time tilt work, the angle should be less than 5 degree; and if for a short time tilt work, the angle should be less than 45 degree.

3. The refrigerator should be ventilated well so as to dissipate heat. The recommended space for the back is more than 200mm and for the sides are more than 100mm.

4. The refrigerator should be away from the heat source and direct sunlight.

5. The refrigerator should be placed in the car or on the floor horizontally and stably.

6. Use dry towels to absorb the remaining water from condensation. Never reverse or tilt the refrigerator to pour the remaining water. Dry the refrigerator if it gets wet by rain. Do not soak the refrigerator in water

7. For refrigerator with a trolley handle, it is prohibited to move it if the electricity is on. It is not recommended to move it if the floor is not smooth. 8. Do not use it if the refrigerator is tilted. If the refrigerator is drawn to a place for use, please leave it upright for 10 minutes before use.

Operations for LCD touch screen

--ON/OFF button: Connect the refrigerator to the power supply and press the ON/OFF button once, and the display will be on to show the environmental temperature. It is recommended to switch on the cooling after the 3-minute delay protection. Press the ON/OFF button again, the refrigerator will be off.

--After you press ON/OFF button, you can set the temperature range from -25℃ to 20℃. Short press "+" and "-" button, or long press "+" and "-" button to adjust the temperature.

-- Long press SET button for 3 seconds and enter advanced parameter mode:

Voltage protection mode:

The machine has three battery protection functions, which protect the normal operation of the refrigerator and protect the battery of the vehicle. The three functions are H3 (high), H2 (medium) and H1 (low). Short press "+" or "-" button to choose the function. The function is set at "H2" (medium) protection when the refrigerator is finished at the factory.

It is recommended to set the battery protection at H2 (medium) when it is used in the car.

It is recommended to set the battery protection at H2 (medium) or H1 (low) if it is external battery or backup battery.

Because of the difference in voltage output from different vehicle power supply output, if there is voltage protection (display screen shows F1), the battery function could be reduced to a lower one (H3 is adjusted to H2 or H1).

If to use the refrigerator after the car engine runs out of fire, please adjust the battery protection at H3 (high). Otherwise, there may be a situation where the battery power of the car is too much consumed to start the vehicle.

Specification

Parameter Table

Common temperature setting

• Red wine storage (10℃),

•Vaccine, Insulin (2℃- 8℃),

•Fruit (4℃- 6℃),

•Beverage (2℃-5℃),

•Meat (-10℃),

•Ice cream (-15℃);

Please be careful if you want to store drugs in the refrigerator.

The three voltage parameters as below:

H3 (high): 10.9V (stop) --12.2V (start voltage)
23.8V (stop) --25.2V (start voltage)
H2 (medium): 9.7V (stop) --11.0V (start voltage)
21.5V (stop) --22.9V (start voltage)
H1 (low): 9.6V (stop) --10.9V (start voltage)
21.3V (stop) --22.7V (start voltage)

Product certificates introduction

Our products have passed LVD / EMC / CE / ROHS / REACH certification

Our Sample policy

We will charge the sample if you want to get a sample and check the quality before you place an official order.

And the freight by Fedex or DHL is on your side. We promise to minus the sample cost from the amount of your

official order in the near future. Thanks for your understanding.

LCD touch sreen with digital thermostat

Q&A

​Q1. How do you pack your products?

A: We pack it with EPS and 5-layer carton box .

Q2. Can we print our logo on the product and carton box?

      A: If you have legally registered patent, we can pack the goods in your branded boxes after getting your authorization letters.
Q3. What is your payment term?
A: T/T 40% as deposit, and 70% before delivery. We'll show you the photos of the products and packages before you pay the balance.
Q4. What is your price term?
A: FOB, CFR, CIF ETC
Q5. What’s your lead time for production?
A: Generally, it takes about 25 to 30 days after receiving your advance payment.

The specific delivery time depends on the items and the quantity of your order.
Q6. Can you produce based on our sample?
A: Yes, we can produce by your samples or technical drawings. We can open the molds just for you.
Q7. What is your sample policy?
A: We will charge the sample if you want to get a sample and check the quality before you place an official order.

And the freight by Fedex or DHL is on your side

 
How to contact us