Allen Bradley Modules 1785 PFB 1785-PFB AB 1785PFB SOFTWARE PROFIBUS MANAGER

Product Specification

Allen Bradley Modules 1785-PFB 1785 PFB AB 1785PFB SOFTWARE PROFIBUS MANAGER

Product Description:

After starting RSLogix 5000 and either starting a new project or opening an existing project, make sure
that you are OFFLINE with the ControlLogix processor. I/O configuration is only available when offline.
If you have not already defined the contents of your ControlLogix chassis under your project's "I/O
Configuration" folder, you will need to define the ControlNet bridge module at a minimum. Use the right
mouse button to click on the "I/O Configuration" folder, then choose "New Module" from the pop-up menu.From the dialog box that appears, choose the ControlNet bridge of the type (1756-CNB or 1756-CNBR)and series that you are using. In the next screen, you will need to name the ControlNet bridge and
indicate its position in the ControlLogix chassis (slot 0 is the leftmost).After defining the ControlNet bridge, use the right mouse button to click on the ControlNet bridge under"I/O configuration", then choose "New Module" from the pop-up menu

Related Product Recommendation:

Product's Character:

The ground conductor of the motor cable should be connected to the drive ground (GRD) terminal directly. Connecting this ground conductor to a cabinet ground point or ground bus bar may cause high frequency current to circulate in the ground system of the enclosure. The motor end of this ground
conductor must be solidly connected to the motor case ground. Shielded or armored cable may be used to guard against radiated emissions from the motor cable. The shield or armor should be connected to the drive ground terminal and the motor ground as outlined in the Grounding section of this Installation
chapter. Common mode chokes are recommended at the drive output to reduce the common mode noise. An RFI filter can be used and in most situations provides an effective reduction of RFI emissions that may be conducted into the main supplylines. If the installation combines a drive with sensitive devices or circuits,it is recommended that the lowest possible drive PWM frequency be programmed.

1771-P4 Power Supply Module AB
1771-P4R Power Supply AB
1771-P4S Power Supply Module AB
1771-P4S1 Power Supply AB
1771-P5 Power Supply AB
1771-P5E Power Supply AB
1771-P6R Power Supply AB
1771-P6S Power Supply AB
1771-P6S1 Power Supply AB
1771-P7 Power Supply AB
1771-PA Power Supply Module AB
1771-PS7 Power Supply Module AB
1771-PS7C Power Supply Assy. 120/220 AC AB
1771-QB Linear Positioning Module AB
1771-RTP4 TYP UMK-SE 11,25-1 902-RTP Remote Termination Panel AB 1
1771-SDN/B 1771-SDN Devicenet Scaner Module AB
1771-SIM Simulator Module AB
1771-SN Sub I/O Scanner Module AB
1771-VHSC Very High Speed Counter Module AB
1771-WA Field Wiring Arm AB
1771-WB Field Wiring Arm,12 Terminals AB
1771-WC Field Wiring Arm AB
1771-WD Field Wiring Arm,12 Terminals AB
1771-WH Field Wiring Arm, 16 I/O channels (21 terminals) AB
1771-WN Field Wiring Arm 32 Terminals AB
1772-CS Processor/Scanner Interconnect Cable AB
1772-LH Processor Interface Module AB
1772-LN2 CPU Module AB
1772-LP2 PLC-2/20 PLC-2/20 Processor Unit AB
1772-LP3 PLC-2/30 PLC-2/30 Processor Unit AB

A to Z Electronics 50312640000 ASA Board Assy AMAT SemVision cX used working

AMAT RadiSys WHC DR 300 0650-A0750 Computer 2A01640AA4A AMAT SemVision cX workin

HiTek G303/51 High Voltage Power Supply & Cable AMAT 50414710200 used working

AMAT SemVision cX CVC Board 50312570000 working

A to Z Electronics 50312403000 HV Module Assy CDM3-i AMAT SemVision cX working

Parker Veriflow 45700342 Point of Use Regulator SQ140E503PLFSFFM used working

ZTE B9100 ZXMBW BaseBand Unit Type B used working

CMC BMR2005TCD00CEA001 PM Servo Motor w/ RHS-20-50-CC-SP Actuator used working

ASM 2506661-21 Circuit Board Revision B Used Working

ASM 2976285-21 Circuit Board Revision A1 Used Working

ASM 2894203-21 Circuit Board Revision A1 Used Working

ASM 2548860-21 Circuit Board Revision A1 Used Working

ASM 2506556-21 Circuit Board Revision A3 Used Working

ASM 2506416-21 Circuit Board Revision A1 Used Working

AMAT 0021-11486 004 Shutter Pentagon cleaned used working

AMAT 0041-38981 RF Ground Shield Source 300mm RF PVD used working

ASM 2850125-21 Circuit Board Revision B Used Working

The use of the product: