Allen Bradley Modules 1336F-MCB-SP1C 1336F MCB SP1C AB 1336FMCBSP1C MAIN CONTROL

Product Specification

Allen Bradley Modules 1336F-MCB-SP1C 1336F MCB SP1C AB 1336FMCBSP1C MAIN CONTROL PCB affordable price

Product Description:

Advanced multi-processor design for leading-edge velocity loop bandwidth, fully digital current, velocity, and position loopsLarge-scale integration with custom ASICs and IPMs for performance and reliabilityA 16-bit A/D convertor for precise velocity command input Flash memory for simple field upgrades A personality module to store setup parameters and simplify drive replacement Reduced component count for reliability Internally-shielded filters for electromagnetic compatibility (EMC) Four dedicated I/O plus eight user-selectable, optically isolated digital inputs and outputs (sourcing/active high):Two dedicated inputs Two dedicated outputs Four user-selectable inputs Four user-selectable outputs Two analog inputs for external current limit Two analog outputs for variable monitoring or torque sharing The purpose of this manual is to provide the user with the necessary information to install, program, start up and maintain the Bulletin 1305 drive. To assure successful installation and operation, the material presented must be thoroughly read and understood before proceeding. Particular attention must be directed to the ATTENTION and Important statements contained within.

Related Product Recommendation:

Product's Character:

The ground conductor of the motor cable should be connected to the drive ground (GRD) terminal directly. Connecting this ground conductor to a cabinet ground point or ground bus bar may cause high frequency current to circulate in the ground system of the enclosure. The motor end of this ground
conductor must be solidly connected to the motor case ground. Shielded or armored cable may be used to guard against radiated emissions from the motor cable. The shield or armor should be connected to the drive ground terminal and the motor ground as outlined in the Grounding section of this Installation

chapter. Common mode chokes are recommended at the drive output to reduce the common mode noise. An RFI filter can be used and in most situations provides an effective reduction of RFI emissions that may be conducted into the main supply lines. If the installation combines a drive with sensitive devices or circuits, it is recommended that the lowest possible drive PWM frequency be programmed.

1745-C2 Interconnect Cable AB
1745-C2 B Interconnect Cable, Series B AB
1745-C3 SLC 150 Interconnect Cable AB
1745-C3 A SLC 150 Interconnect Cable, Series A AB
1745-E101 Expansion Unit AB
1745-E102 Expansion Unit AB
1745-E103 Expansion Unit AB
1745-E104 Expansion Unit AB
1745-E105 Expansion Unit AB
1745-E106 Expansion Unit AB
1745-E107 Expansion Unit AB
1745-E151 SLC 150 Expansion Unit AB
1745-E152 SLC 150 Expansion Unit AB
1745-E153 SLC 150 Expansion Unit AB
1745-E154 SLC 150 Expansion Unit AB
C SLC 150 High Speed Input Module AB
1745-E156 SLC 150 Expansion Unit AB
1745-E157 SLC 150 Expansion Unit AB
1745-LP101 Processor Unit AB
1745-LP102 Processor Unit AB
1745-LP103 Processor Unit AB
1745-LP104 Processor Unit AB
1745-LP151 SLC 150 Processor Unit AB
1745-LP152 SLC 150 Processor Unit AB
1745-LP153 SLC 150 Processor Unit AB
1745-LP154 SLC150 SLC 150 Processor Unit AB
1745-LP156 SLC 150 Processor Unit AB
1745-LP157 SLC 150 Processor Unit AB
1745-M1-- EEPROM Memory Module AB
1745-PCC SLC Personal Computer Interface Converter AB

1745-PT1 Hand Held Programmer AB
1745-TCAT TCAT SLC-100 Timer Counter Access Terminal AB
1746-A10 10-Slot Chassis AB
1746-A13 13-Slot Chassis AB

The use of the product: