6000 Aluminium Industrial Profile Aluminum Formwork Set For Building Project

Product Specification

6000 Series Aluminum Formwork Set for Building Project Aluminium Industrial Profile

Aluminum Formwork Installation:

Aluminum Formwork Installation Disclosure

1-2 days before installation of the first layer of aluminum formwork,the person in charge of aluminum formwork shall organize relevant operators to be familiar with the installation coding diagram of aluminum formwork and conduct division disclosure.

Construction Setting Out

After the concrete pouring is completed and the floor concrete reaches a certain strength,the construction positioning and setting out shall be carried out immediately, and the positioning line of wall column shall have zero error.

Ground Elevation Inspection and Chiseling

The elevation and mark shall be conducted along the positioning line of the wall column. After the straightening is completed, the part higher than the concrete shall be removed with a large crowbar or electric pick to make it slightly lower than the structural elevation.

Welding of Positioning Reinforcement

There shall be no false welding in the welding process,
and the duration of each welding shall be ≤ 5 seconds,
welding space of positioning bar ≤ 1000mm

Lifting Formwork, Node Removal

During the construction and setting out, the formwork shall be lifted and the nodes shall be removed simultaneously. During the folding process, it is not allowed to smash and pry hard, and the finished concrete products shall be protected from damage.

Remove the Aall Column Formwork

After the formwork removal conditions are met or the formwork removal is approved, the wall column formwork shall be removed. Before the removal of the wall column formwork, the diagonal brace, steel wire rope and other fasteners shall be removed first.

Wall Column Formwork Transfer

After the removal of the wall column and floor slab, the whole body shall be coated with the release agent, which shall be transferred to the corresponding position in sequence according to the formwork installation sequence, the formwork code.

Wall Column Formwork Installation

The wall column slab shall be transferred to the corresponding position,and the wall column formwork shall be installed after the completion of embedded acceptance of Rebar,water and electricity.

Initial Adjustment of Wall Column Formwork

After the wall column formwork is installed, the elevation adjustment and the initial adjustment of verticality of the wall column formwork shall be carried out immediately. Before the initial adjustment, the verticality error shall be calibrated ≤ 3mm.

Remove the Beam Formwork

After the internal wall formworks are all transferred to the installation layer, the beam formworks shall be removed. Before the formworks are removed, it shall be confirmed that the work bench is safe and reliable, and there is no other material around.

Beam Formwork Installation

Before the installation of beam bottom formwork, confirm that the connection of beam bottom formwork is stable, the beam bottom installation is completed and the support is stable before the installation of beam side formwork.

Remove the Floor Formwork

After all the beam formworks are transferred to the installation floor, the floor formworks shall be removed. The bottom cage shall be removed first, then the panel shall be removed, and finally the floor C shall be removed.

Floor Formwork Installation

The beam formwork shall be installed firmly, and the floor formwork shall be installed. Before installation, it shall be confirmed that the bottom cage is supported firmly as required.

Specifiaction of Profile:

Photos:

Characteristics:

The density of aluminum profile is only 2.7g/cm3, about one third of that of steel, copper or brass (7.83g/cm3, 8.93g/cm3). Aluminum exhibits excellent corrosion resistance under most environmental conditions, including air, water (or brine), petrochemicals, and many chemical systems.

Conductivity

Aluminum profile is often selected because of its excellent conductivity. Aluminum is almost twice as conductive as copper by weight.

Rate thermal conductivity

The thermal conductivity of aluminum alloy is about 50-60% of that of copper. It is used to manufacture heat exchangers, evaporators, heating appliances, cooking utensils, cylinder heads and radiators for automobiles.

Ferromagnetic

Aluminum profiles are non ferromagnetic, which is an important feature of the electrical and electronic industries. Aluminum profiles do not self ignite, which is very important for applications involving handling or contacting flammable and explosive materials.

Machinability of can making machine

The processing performance of aluminum profile is excellent. In the process of deformation and casting of aluminum alloy, as well as in various states after the output of aluminum alloy, the processing characteristics change greatly, which requires a special machine tool or process.

Formability

Specific tensile strength, yield strength, ductility and corresponding work hardening rate determine the variation of allowable deformation.

Circularity

Aluminum is very recyclable, and the performance of recycled aluminum is almost indistinguishable from that of natural aluminum.

Please tell us the information below, and we will give the best suggestion to you !

1. Where you intend to use the aluminium profiles?

2. If you have the estrusion drawing, send us and we develop the correspondence mold.

3. Which color you want or tell us the architectural style you like.

4. Purchase quantity. It will convenient us to give you the best price.