0.8-1.2mm Thickness Aluminum Window Profiles Set 6063

Product Specification

Aluminum Profiles Set For Aluminium Windows Frame Anodized Surface 0.8-2.0mm Thickness

Aluminum Windows Doors:

Aluminum alloy doors and windows refer to doors and windows made of aluminum alloy extruded profiles as frames, stiles and fans, called aluminum alloy doors and windows, or aluminum doors and windows for short. Aluminum alloy doors and windows include wood and plastic composite doors and windows that use aluminum alloy as the base material of the force-bearing member (the rod that bears and transfers its own weight and load), referred to as aluminum-wood composite doors and windows, and aluminum-plastic composite doors and windows.

Profile Specification:

Aluminum Profiles Features:

Corrosion resistance
The density of aluminum profile is only 2.7g/cm3, which is about 1/3 of that of steel, copper or brass (7.83g/ cm3, 8.93g/ cm3, respectively). In most environmental conditions, including in air, water (or salt water), petrochemistry and many chemical systems, aluminum can show excellent corrosion resistance.
conductivity
Aluminum profile is often selected for its excellent conductivity. On the basis of equal weight, the conductivity of aluminum is nearly 1/2 of copper.
Thermal conductivity
The thermal conductivity of aluminum alloy is about 50-60% of copper, which is beneficial to the manufacture of heat exchanger, evaporator, heating appliance, cooking utensil, cylinder head and radiator of automobile.
Nonferromagnetism
Aluminum profile is non ferromagnetic, which is an important feature for the electrical and electronic industries. Aluminum profiles cannot be self ignition, which is important for the application of handling or contacting inflammable and explosive materials.
Processability
The processability of aluminum profile is excellent. In various deformation and casting aluminum alloys, and in the various states after the production of these alloys, the machining characteristics have changed greatly, which requires special machine tools or technologies.
Formability
The allowable deformation is controlled by specific tensile strength, yield strength, ductility and corresponding processing hardening rate.
Recyclability
Aluminum has high recovery, and the characteristics of recycled aluminum are almost the same as that of primary aluminum.

Product Description:

Oxidation Technology Introduction:

Aluminum or aluminum alloy products are used as anodes in electrolyte solution, and the process of forming aluminum oxide film on the surface of the aluminum and aluminum alloy is called anodic oxidation treatment of aluminum and aluminum alloy. After anodization, the surface of aluminum can produce several microns - hundreds of microns of oxide film. Compared with the natural oxide film of aluminum alloy, its corrosion resistance, wear resistance and decoration have been obviously improved and improved.

- The aluminum oxide film is a porous membrane. Whether it is coloured or not, it must be closed before being put into use, so as to improve its corrosion resistance and weatherability. There are three kinds of treatment methods, namely, high temperature hydration reaction closed, inorganic salt closure and organic matter closure.

(1) High temperature water sealing.

This method utilizes the hydration reaction of aluminum oxide film and water to turn the amorphous membrane into a hydrated crystalline membrane.

The hydration reaction can be carried out at both normal and high temperatures, but at high temperatures, especially at the boiling point, the hydrated crystalline membrane is a very stable and irreversible crystalline film. Therefore, the most commonly used aluminum oxide film is treated by boiling water or steam treatment.

(2) Sealing of inorganic salts.

Inorganic salt method can improve the fastness of organic coloring dyes, so it is often used in chemical coloring.

(3) Organic sealing method.

This is the soaking, soaking or coating of the aluminum oxide film. Because of the high cost and the increase of the process flow, it is not easy to use, more or more of the two kinds of methods mentioned above, and the first kind of high temperature hydration is the mainstream.

FAQ:

Q – What is the average lead time for pre production samples?

A – Our average lead time is normally 7 days for making new samples and 7 days for testing , totally need about 14days.

Q – What is the average lead time for mass production?

A – Our average lead time is delivery within 20-30 days after receive deposit and and moulds/samples are passed.

Q – What is CAD?

A – CAD stands for “computer assisted design” and it is a 3-D program that is used by our clients to provide our technicians with a three-dimensional example of the custom shape that they want made at GUANGDONG YONGLONG ALUMINUM.Aluminium Window Profiles

Q – What is a die?

A – A die is a tool that is used to help forge a custom shape during the extrusion process. The die is made from durable steel so that it can be used again and again to fill the client’s order.

Q – What does extrusion mean?

A – Extrusion is the process that is used to create custom shapes from raw aluminum materials according to a client’s specifications. The raw materials are heated and are then forced through a die to create the desired shape using extreme pressure.

Welcome to visit our company !

Choose us & contact us !