ShenZhen Vector Technology Co., Ltd.
| Payment Terms | T/T, Western Union, L/C |
| Supply Ability | 500 kits/month |
| Delivery Time | 3-5 work days |
| Packaging Details | 280*208*78mm,375*290*155mm |
| Voltage | 380V |
| Power | 11KW |
| Phase | Three Phase |
| Communication Protocols | Modbus/EtherCAT/CanOpen |
| Encoder | 17/23/24 bit absolute encoder |
| Rated Current | 27A |
| Input | Pulse |
| Control Mode | Position / Speed / Torque |
| Application | Construction Machine |
| Brand Name | Vector |
| Model Number | VEC-VC-02733H-M-E |
| Certification | CE |
| Place of Origin | China |
View Detail Information
Explore similar products
220V AC Servo Drive OEM Uper 250KW For Printer Packing Machine
CE 380V 3KW Programmable Servo Drive For Food Packing Machine
Three Phase 1.5KW AC Servo Drive With 2500 Lines Incremental Hall Encoder
1KW AC Servo Amplifier Three Phase Programmable For Robotics
Product Specification
| Payment Terms | T/T, Western Union, L/C | Supply Ability | 500 kits/month |
| Delivery Time | 3-5 work days | Packaging Details | 280*208*78mm,375*290*155mm |
| Voltage | 380V | Power | 11KW |
| Phase | Three Phase | Communication Protocols | Modbus/EtherCAT/CanOpen |
| Encoder | 17/23/24 bit absolute encoder | Rated Current | 27A |
| Input | Pulse | Control Mode | Position / Speed / Torque |
| Application | Construction Machine | Brand Name | Vector |
| Model Number | VEC-VC-02733H-M-E | Certification | CE |
| Place of Origin | China | ||
| High Light | Pulse Input AC Servo Motor Driver ，Vector 11KW AC Servo Motor Driver ，Internal Planning Position AC Servo Drive | ||
Vector Pulse Input AC Servo Motor Driver Internal Planning Position
Products Description
| Product Name | AC Servo Motor Driver |
| Brand | Vector |
| Model No. | VEC-VC-02733H-M-E |
| Power4 | 11KW |
| Voltage | 380V |
| Phase | Three Phase |
| Rated Current | 27A |
| Communication Protocols | Modbus/CANopen/EtherCAT |
| Encoder | 17/23/24 bit absolute encoder |
How is the Servo Drive works? The Location control model, Speed control model and Trogue control model.
| Pulse Command Input | Pulse Type | Differential input,Open collector |
| Frequency Range | Differential input:0-500kHz,pulse width greater than 1us Open collector: 0-300kHz,pulse width greater than 2.5us | |
| Pulse Mode | pulse + direction; AB pluses; CW+CCW; | |
| Analog Input | Voltage Range | -10V to 10V |
| Input Impedance | 10kΩ |
Servo Drive Description- Details about a Servo Drive, how to select the Servo drive model and do installation?
The panel contains 8 buttons and 5 digital tubes. Only 5 of the 8 buttons can be used, and the
remaining 3 buttons reserved. The general functions of the five buttons are shown in the table below.
| Key Name | Key function |
| PAR/ALM | mode switch, return to the previous menu |
| ▲(add) | increase flashing bit value of the LED digital tube |
| ▼(dec) | Decrease flashing digit value of the LED digital tube |
| STOP/RST | Moves the blinking LED tube to the left; checks the high value of data longer than 5 bits; Fault reset;execute Fn function |
| RD/WT | read/write parameter values;enter fn page |
Wiring precautions
● It is recommended not to use single-phase 220V for main power supply,
which may cause damage to electrolytic capacitor due to lack of phase.
● Do not change the wiring during power-on, otherwise it may cause electric
shock or injury.
● Please perform wiring or inspection by professional technicians, otherwise it
may cause electric shock or product failure.
● Please carefully confirm the wiring and power supply. The output circuit
may be short-circuited due to wiring errors or application of different voltages. The brake does not operate when the above fault occurs, which may result in mechanical damage or personal injury.
● Do not connect the input power cable to the U, V, and W terminals of the
drive. Otherwise, the servo driver will be damaged.
● When wiring, do not pass the power cable and signal cable through the same
pipe, and do not bundle them together. The distance between the two should be more than 30cm to avoid interference.
● The driver ground terminal must be grounded to avoid leakage and reduce
the interference of the system, and the diameter of the ground wire should be the same as or above the power supply line.
● When connecting the AC power supply and DC power supply to the servo unit, connect to the specified terminal. Failure to do so may result in malfunction or fire.
● For the wiring length, the command input line is up to 3m and the encoder
line is up to 20m.
● Use a twisted-pair shielded cable for the signal cable and encoder cable, and
ground the shield with a single end.
●The U, V, W terminals of the driver and the U, V, and W terminals of the
motor should be connected one by one according to the name. If it is wrong connected, the motor cannot operate normally.
● Common DC bus products require pressure sensitive resistors and the wiring
is secure.
● Please check the power after the power is off for at least 5 minutes. Even if
the power is turned off, high voltage may remain inside the servo drive. Therefore, do not touch the power terminal within 5 minutes after the power is turned off, otherwise it may cause electric shock.
● Do not turn the power ON/OFF frequently. When it is necessary to
continuously turn ON/OFF the power, please control it once or less in 1 minute. Since the power supply section of the servo driver has a capacitor, a large charging current (charge time of 0.2 seconds) flows during the ON/OFF power supply. Therefore, if the power is turned ON/OFF frequently, the performance of the main circuit components inside the servo driver will be degraded.
● Do not apply power when the terminal block screws are loose or the cable is
loose. Otherwise, it may cause fire.
● Take appropriate shielding measures in the following locations, otherwise
the machine may be damaged:
1. Locations that cause interference due to static electricity;
2. A place that produces a strong electric field or a strong magnetic field;
3. Locations where there may be radiation radiation;
4. A place with a power cord nearby.
Certificates
1. CE (EU Safety Standard);
2. IEC/EN61800-5-1:2007 (Safety requirements for electrical, thermal and energy in Section 5-1 of
the variable speed electric driver system), corresponding to the national standard GB12668.501-2013;
3, IEC / EN61800-3: 2004 + A1 (speed control electric driver system part 3 electromagnetic compatibility
standards and its specific test methods), corresponding to the national standard GB12668.3-2012.
Quality Checking:
Four times Production testing
Two Times 24 hoursTesting
100% Inspection Before Shipping
Delivery Time and Shipping Way
1. For small order we always can delivery out within 1 week.
2. Our products can be shippied via Air, Land or Sea.
| Quantity | 1-5 kits | 50-100 kits | 200-500 kits |
| Delivery time | Within 3 days | 5-10 days | 15-25 days |
| Packing details of Servo Drive | |||||
| Products | E1(3-6A) | E2(7-12A) | E3(16-27A) | C015(32-38A) | C022(45-60A) |
| Ctn. Size | 280*208*78 | 280*208*112 | 375*290*155 | 440*296*288 | 510*305*325 |
Exhibition:
Company Details
Business Type:
Manufacturer,Exporter
Year Established:
2004
Total Annual:
100,000,000-200,000,000
Employee Number:
50~100
Ecer Certification：
Active Member
Focusing on industrial automation products with independent intellectual property rights, we are positioned to serve high end equipment manufacturers and provide overall solutions for customers in market segments. To become the world's leading provider of industrial automation products and solut... Focusing on industrial automation products with independent intellectual property rights, we are positioned to serve high end equipment manufacturers and provide overall solutions for customers in market segments. To become the world's leading provider of industrial automation products and solut...
Get in touch with us
Leave a Message, we will call you back quickly!